由 MST Engineering 根据英文原文翻译。 查看原文
Coilcraft XAL4020-221MEC vs MAZO VCMA-0420-R22-M-1A
Verdict: Not a replacement on an existing XAL4020 layout.
The MAZO pads span 5.2 mm against 3.35 mm, the body is larger and the heating current is 29 % lower (12 A typ / 10 A max vs 16.8 A). On a new layout at 10 A RMS or less and 40 V or less it is a candidate to evaluate.
MAZO VCMA-0420-R22-M-1A
New layout, ≤ 10 A RMS: design to the 10 A MAX column. Does not fit XAL4020 pads.
MAZO VCMA-0630-R22-M-1A
New layout above 10 A RMS: 24.5 A typ / 24 A max heating current, 75 V, 7.3 × 6.8 × 3.0 mm max. Does not fit XAL4020 pads.
XAL4020 alternatives for new layouts, value by value
Not an equivalent part. Verify ripple, temperature rise and EMI in your circuit. Freight, duties and tax are confirmed separately; transit time comes on top of dispatch preparation.
数据手册关键参数(Coilcraft Document 806,修订日期 02/25/26)

| 参数 | XAL4020-221ME_ | 条件/脚注 |
|---|---|---|
| 电感量 | 0.22 µH ±20 % | 测试条件为 1 MHz、0.1 Vrms、0 Adc |
| DCR | 典型值 5.81 mΩ,最大值 6.40 mΩ | 使用微欧计测量 |
| SRF | 典型值 191 MHz | |
| Isat | 18.7 A | 在 25 °C 下使电感量下降 30 %(典型值)的直流电流 |
| Irms | 12.0 A(温升 20 °C),16.8 A(温升 40 °C) | 在 25 °C 环境温度下引起相应温升的电流;仅供参考,须在实际应用中验证 |
| 工作电压 | 60 V | 脚注:耐压能力因零件编号而异 |
| 环境温度 | 在 Irms 电流(温升 40 °C)下为 –40 °C 至 +125 °C | 元件最高温度 +165 °C(环境温度 + 温升) |
| 尺寸 | 4.0 ±0.3 × 4.0 ±0.3 mm(最大 4.3 mm),最大高度 2.1 mm | 重量 0.17–0.18 g |
| 资质与合规 | 通过 AEC-Q200 验证;符合 RoHS,无卤 | |
| MSL | 1 | 在 < 30 °C / 85 % RH 下,拆封后车间存放寿命不限 |
解析后缀 "MEC"

需要按相同条件比较的项目
- 不同制造商对 Isat 的定义不同。 Coilcraft 采用电感量下降 30 % 的判据;其他数据手册可能采用 20 % 或 30 %。应在相同定义下比较。
- Irms 由热条件决定,并非绝对额定值。 Coilcraft 说明,温升取决于 PCB 焊盘图形、走线尺寸、气流和邻近元件。
- 电感量测试频率不同。 Coilcraft 的测试条件为 1 MHz、0.1 Vrms。采用 100 kHz 或 1 V 测试的零件不能直接比较。
- 焊盘图形。 应采用 Coilcraft 数据手册第 4 页推荐的焊盘图形。