MST
RFQ cartCart

XAL4020-221MEC: Coilcraft 0.22 µH power inductor datasheet values and RFQ notes

Need a part from this thread? Let MST find it

This thread is attached to your request. Add the part, your email and quantity; no account needed.

Can't find this part? We'll source it

Send us the part number and quantity. An MST engineer will source it, check that it fits your application, and reply with a quote.

Coilcraft XAL4020-221MEC vs MAZO VCMA-0420-R22-M-1A

Verdict: Not a replacement on an existing XAL4020 layout.

The MAZO pads span 5.2 mm against 3.35 mm, the body is larger and the heating current is 29 % lower (12 A typ / 10 A max vs 16.8 A). On a new layout at 10 A RMS or less and 40 V or less it is a candidate to evaluate.

MAZO VCMA-0420-R22-M-1A

Price on the product page or by quote.

New layout, ≤ 10 A RMS: design to the 10 A MAX column. Does not fit XAL4020 pads.

MAZO VCMA-0630-R22-M-1A

Price on the product page or by quote.

New layout above 10 A RMS: 24.5 A typ / 24 A max heating current, 75 V, 7.3 × 6.8 × 3.0 mm max. Does not fit XAL4020 pads.

Not an equivalent part. Verify ripple, temperature rise and EMI in your circuit. Freight, duties and tax are confirmed separately; transit time comes on top of dispatch preparation.

Short answer: XAL4020-221MEC is a Coilcraft XAL4020-series shielded power inductor: 0.22 µH ±20 %, DCR 5.81 mΩ typical / 6.40 mΩ maximum, Isat 18.7 A (30 % inductance drop, typical), Irms 12.0 A (20 °C rise) / 16.8 A (40 °C rise), on a 4.0 × 4.0 mm footprint with 2.1 mm maximum height. All values below are taken from Coilcraft's XAL40xx datasheet (Document 806, revised 02/25/26). Check that document before ordering; it is the reference, not this page.

Key datasheet values (Coilcraft Document 806, revised 02/25/26)

Bar chart of Coilcraft XAL4020-221ME current ratings: Irms 12.0 A at 20 °C rise, Irms 16.8 A at 40 °C rise, and Isat 18.7 A at 30 % inductance drop, with 0.22 µH, 5.81 mΩ typical DCR and 191 MHz SRF noted
ParameterXAL4020-221ME_Condition / footnote
Inductance0.22 µH ±20 %Tested at 1 MHz, 0.1 Vrms, 0 Adc
DCR5.81 mΩ typ, 6.40 mΩ maxMeasured on a micro-ohmmeter
SRF191 MHz typ
Isat18.7 ADC current at 25 °C causing a 30 % (typ) inductance drop
Irms12.0 A (20 °C rise), 16.8 A (40 °C rise)Current causing that temperature rise from 25 °C ambient; reference only, verify in application
Operating voltage60 VFootnote: capability varies by part number
Ambient temperature–40 °C to +125 °C with (40 °C rise) Irms currentMaximum part temperature +165 °C (ambient + rise)
Size4.0 ±0.3 × 4.0 ±0.3 mm (4.3 mm max), height 2.1 mm maxWeight 0.17–0.18 g
QualificationAEC-Q200 qualified; RoHS compliant, halogen free
MSL1Unlimited floor life at < 30 °C / 85 % RH
Electrical specifications are at 25 °C.

Decoding the suffix "MEC"

Part-number decoding diagram for XAL4020-221MEC: XAL4020 series, 221 inductance code for 0.22 µH, M for ±20 % tolerance, E for RoHS tin-silver over copper termination, C for 7-inch machine-ready reel packaging
Coilcraft's ordering note says to specify termination and packaging codes. In `XAL4020-221MEC`, E is the termination (RoHS tin-silver over copper) and C is the packaging: a 7″ machine-ready reel (EIA-481 embossed plastic tape). XAL4020 ships 1000 per 7″ reel or 3500 per 13″ reel (D = 13″ reel, factory order only). The datasheet also says B (less than full reel) is being replaced: change the last letter from B to C. So `XAL4020-221MEB` and `XAL4020-221MEC` are the same electrical part with different packaging. T and S are special-order terminations (tin-silver-copper; non-RoHS tin-lead).

Things to compare like for like

  • Isat definitions differ between makers. Coilcraft uses a 30 % inductance drop; other datasheets may use 20 % or 30 %. Compare at the same definition.
  • Irms is thermal, not an absolute rating. Coilcraft notes temperature rise depends on PCB land pattern, trace size, airflow and nearby parts.
  • Inductance test frequency differs. Coilcraft tests at 1 MHz, 0.1 Vrms. A part tested at 100 kHz or 1 V is not directly comparable.
  • Land pattern. Use the recommended land pattern on page 4 of the Coilcraft datasheet.

Existing comparison on this community

MST Engineering has already published a datasheet comparison with a MAZO part: Can VCMA-0420-R22-M-1A replace XAL4020-221MEC? A datasheet comparison. Its conclusion is that interchangeability has not been established. The two share a nominal 0.22 µH, but their test conditions, rated voltage (60 V vs 40 V), maximum part temperature (165 °C vs 125 °C) and land patterns differ. Treat VCMA-0420-R22-M-1A as a candidate to verify in your design, not as a drop-in.

What to send in an RFQ

1. Full part number including the suffix (e.g. XAL4020-221MEC), quantity and whether cut tape or full reel is acceptable. 2. Genuine Coilcraft only, or open to an alternative for evaluation. 3. If an alternative is acceptable: switching frequency, peak and RMS current, voltage, ambient temperature, and the land pattern you must keep.
Coilcraft is a trademark of Coilcraft, Inc. Names and part numbers are used for identification only. MST is not affiliated with or endorsed by Coilcraft.

Original OEM documents (links only)

1. Coilcraft, "Shielded Power Inductors – XAL40xx" datasheet, Document 806, revised 02/25/26 (page 1: values and footnotes; page 4: dimensions, land pattern, packaging). https://www.coilcraft.com/getmedia/6adcb47d-8b55-416c-976e-1e22e0d2848c/xal4000.pdf 2. Coilcraft XAL family page (lists XAL40xx at 4.3 × 4.3 × 2.1 mm max). https://www.coilcraft.com/en-us/products/power/shielded-inductors/molded-inductor/xal/xal4020/

Request a quote

Need XAL4020-221MEC or a qualified alternative? Post a find-part request or send a sourcing RFQ. MST replies in the thread or by email. MST does not claim stock of XAL4020-221MEC; sourcing is done on request.
Parts

Replies (0)

No replies yet.

Can't find this part? We'll source it

Send us the part number and quantity. An MST engineer will source it, check that it fits your application, and reply with a quote.