Short answer: "Same full scale" doesn't make an MFC a drop-in. Before an MKS unit replaces a Brooks unit (or the other way round), check seven things: gas and calibration, full-scale range, fittings and length, I/O type and connector/pinout, supply voltage and power, response/settling, and seals. MKS's own cross-reference chart only maps discontinued MKS models to current MKS models, and even there it warns that "the newer product is not a direct replacement" in some cases. No official MKS↔Brooks cross-reference is cited here. Treat any cross-brand swap as a candidate to verify.

Step 0: is your MFC already obsolete?

The MKS Flow Product Cross Reference Chart (examples, verbatim mapping):
| Discontinued MKS | MKS recommended replacement | Chart note |
|---|---|---|
| 1179A family (via GE50A datasheet) | GE50A | GE50A datasheet: its analog and digital I/O "can easily be used to replace those same I/O types of the 1179A" |
| 1159B, 1162B, 1749A, M100B | GE50A (elastomer-sealed) | — |
| 1160B, 1161B | GE50A | "Contact MKS Applications Engineering for Adapter Cable" |
| 1259C | GE50A | "…for Length Adapter" |
| 1759A | GE50A | Only "for flow rates up to 50 slm, N2 equivalent" |
| 1479A/B, 1480A, 1459C, 1462C | GM50A (metal-sealed) | 1461C also needs an adapter cable |
| 2159B, 2179A/B | GV50A (with shut-off valve) | — |
| 1661A, M200 | P4B | — |
The notes about adapter cables and length adapters are exactly the failure modes you get across brands too.
The checklist, with what the datasheets say
| Check | MKS GE50A | Brooks SLA5850 (SLA5800 Series) | What to verify |
|---|---|---|---|
| Full-scale range (N2 eq.) | 5–50,000 sccm | 0.003–50 slpm | Your FS and gas, not just N2 |
| Control range | 2–100 % FS | 1–100 % FS (100:1 from 1–50 slpm) | Lowest setpoint you actually run |
| Accuracy (cal gas) | ±1 % of reading 20–100 % FS. ±0.2 % FS for 2–20 % FS | ±0.9 % S.P. (20–100 % FS), ±0.18 % FS (<20 % FS), incl. cal-system uncertainty | Same definition and basis |
| Settling / response | <750 ms typical above 5 % FS (SEMI E17-0600) | <1 s (settling within ±2 % FS, 0–100 % step) | Recipe step timing. Definitions differ |
| Analog I/O | 0–5 VDC (9- or 15-pin D) or 4–20 mA (15-pin D) | 0–5 V, 1–5 V, 0–10 V, 0–20 mA, 4–20 mA (15-pin D) | Signal type and pin assignment |
| Supply (analog) | +15 to +24 VDC, <4 W | +13.5 to +27 Vdc. Up to 8 W (orifice >0.032″) | Tool PSU rail and current budget |
| Digital options | DeviceNet, RS485, Profibus, EtherCAT, PROFINET | RS485, Profibus, DeviceNet, EtherCAT, EtherNet/IP, PROFINET | Protocol and EDS/GSD/ESI file |
| Fittings | 4 VCR male, 4 VCO, 1/4″ compression, KF-16, C-seal, others. "Standard 3-inch footprint" | 1/4″ VCR, 3/8–1/2″ VCR, elastomer downport, others | Face-to-face length / footprint drawing |
| Seals | Viton std. Buna-N, Neoprene, EPDM, Kalrez options | Viton, Buna-N, Kalrez, Teflon/Kalrez, EPDM | Gas compatibility |
| Valve | NC or NO | NC, NO, meter | Same default state on power loss |
| Ambient | 10–50 °C | −14 to 65 °C | Enclosure temperature |
| Leak-by (closed valve) | <0.1 % FS (to 10K valve), <1.0 % FS (20K–50K) | <1 % FS standard | MKS: separate shut-off valve needed for zero flow |
Where drop-ins usually fail
1. Connector pinout. Both use 15-pin D-sub on analog versions, but don't assume the pins match. The current GE50A datasheet (10/21) lists only MKS 9-pin and 15-pin analog connector options (including "tied grounds" variants), with no Brooks-compatible pinout code. Compare pin-by-pin against each maker's installation manual before plugging in.
2. Signal range. A 0–5 V tool controller driving a 4–20 mA MFC (or a Brooks 1–5 V unit) gives wrong flow, or none.
3. Gas calibration. Both makers state accuracy on the calibration gas. Order the unit calibrated (or configured) for your process gas and FS. GE50A ordering uses a SEMI E52 gas code (e.g. 013 = N2) plus a 3-digit FS code (e.g. 502 = 5000 sccm). Don't apply a generic gas-correction factor from a third-party table to a substitute and assume the result is in spec. Ask the maker.
4. Length and seals. A different face-to-face length or seal type means a re-plumbed gas stick, not a swap. The MKS chart's "length adapter" note says the same.
5. Digital network files and addressing. DeviceNet MAC ID, Profibus station address and EtherCAT ESI must match the tool's configuration.
6. Pressure differential. GE50A needs 10–40 psid (10–5000 sccm range). SLA5850 needs a minimum of 5 psi. Check your supply pressure.
What to send in an RFQ (engineering + procurement)
- Current MFC: maker, full model / ordering code, serial-label photo
- Gas, full-scale flow, calibration gas required
- I/O: analog type (0–5 V / 4–20 mA…) or protocol, connector, any tool-specific pinout
- Fittings and footprint length; seal material; NC/NO
- Supply voltage available; ambient temperature
- Copy-exact only, or open to a cross-brand candidate for evaluation
- Quantity, need-by date, calibration certificate requirement
MKS is a trademark of MKS Inc. Brooks is a trademark of Brooks Instrument. Names and model numbers are used for identification only. MST is not affiliated with or endorsed by these companies.
Original OEM documents (links only)
1. MKS, "MKS Flow Products Cross Reference Chart" (web page). https://www.mks.com/n/mks-flow-product-cross-reference-chart
2. MKS, "GE50A Elastomer Sealed, Digital Mass Flow Controller" datasheet, GE50A_10/21. https://api.p1.mks.com/mam/celum/celum_assets/resources/GE50-DS.pdf
3. Brooks Instrument, "SLA5800 Series Elastomer Sealed, Digital, General Purpose Gas Mass Flow Controllers & Meters" datasheet, Data-Sheet-SLA5800-EN/2026-07. https://www.brooksinstrument.com/hubfs/Data-Sheet-SLA5800-EN.pdf
4. Brooks Instrument document library (SLA5800 Installation & Operation Manual and protocol supplements, for pinouts). https://sales.brooksinstrument.com/service-support/download-documents
Request a quote
Need a like-for-like MFC or a calibrated candidate for your gas? Post a find-part request with the checklist fields, or send a sourcing RFQ. MST replies in the thread or by email. MST does not claim stock of any model mentioned here; sourcing is done on request.
Parts