MST
RFQ cartCart

Can VCMA-0420-R22-M-1A replace XAL4020-221MEC? A datasheet comparison

Need a part from this thread? Let MST find it

This thread is attached to your request. Add the part, your email and quantity; no account needed.

Can't find this part? We'll source it

Send us the part number and quantity. An MST engineer will source it, check that it fits your application, and reply with a quote.

Interchangeability has not been established. These two inductors share a nominal inductance, but a replacement decision also needs electrical test conditions, thermal limits and the PCB land pattern. This is an MST document comparison, not a completed application test.

1. Compare like-for-like conditions

Coilcraft XAL4020-221MEC, document 806 revised 25 February 2026:
  • Nominal inductance: 0.22 µH ±20%, measured at 1 MHz, 0.1 Vrms, 0 Adc.
  • DCR: 5.81 mΩ typical, 6.40 mΩ maximum.
  • Heating-current reference: 16.8 A for a 40°C rise from 25°C ambient.
  • Isat: 18.7 A at a typical 30% inductance drop, 25°C.
  • Operating voltage: 60 V; maximum total part temperature: 165°C.
MAZO VCMA-0420-R22-M-1A, revision A4 dated 26 November 2025:
  • Nominal inductance: 0.22 µH ±20%, measured at 1 MHz, 1.0 V; RMS is not specified. Table reference ambient: 25°C.
  • DCR: 5.0 mΩ TYP, 5.6 mΩ MAX.
  • Idc: 12.0 A TYP and 10.0 A in the printed MAX column, at approximately 40°C rise from 25°C ambient.
  • Isat: 18.5 A TYP and 17.5 A in the printed MAX column, at approximately 30% inductance drop.
  • Rated voltage: 40 V; maximum total part temperature: 125°C.

2. The ambiguity that must remain visible

MAZO prints current values in the MAX columns that are below the corresponding TYP values. We preserve those labels and values exactly. The document does not resolve the convention sufficiently to relabel them as guaranteed minimum current or absolute maximum current. Obtain manufacturer clarification before using them as design limits.
The lower listed DCR is only a resistance comparison at the reference conditions. It does not establish lower temperature, unchanged efficiency or acceptable ripple in the intended circuit.

3. Check the mechanical drawings too

Compare the actual PCB copper, solder-mask openings, terminal geometry and keep-out against both recommended land drawings. The recommended lands differ. A similar package-family size does not prove that the existing footprint can be reused.

4. Turn the comparison into a decision record

For the actual design, record the switching frequency, current waveform including peak and RMS values, voltage stress, ambient conditions and PCB construction. Define the required inductance under operating bias and the allowed total part temperature. Resolve unknowns before deciding which sample evaluation is justified.
Then document the agreed checks for thermal behavior, electrical performance, transient operation and assembly. A passing result belongs to the tested board, operating envelope and revision; it should not be presented as an unrestricted replacement claim.

5. Read the original PDFs

Coilcraft: page 1 for values and footnotes; page 4 for the land pattern. https://www.coilcraft.com/getmedia/6adcb47d-8b55-416c-976e-1e22e0d2848c/xal4000.pdf
MAZO A4, existing Store-hosted manufacturer document: pages 2–3 for temperature and electrical conditions; page 4 for dimensions and lands. https://mstchip.com/storefront/mazo-datasheets/VCMA-0420/MAZO-VCMA-0420-datasheet-A4.pdf
Documents checked 18 October 2026. No bench test, manufacturer-approved cross-reference or stock confirmation is claimed here. Add the non-confidential design requirement you need to compare in a reply; include its units and operating conditions.
MST technical editorial | Version 1 | 18 October 2026

Parameter comparison

Values and test conditions below retain the wording of the source. A matching value alone does not establish interchangeability.

ParameterVCMA-0420-R22-M-1AXAL4020-221MECAssessment
Nominal inductance0.22 µH
NOMINAL
±20%; 1 MHz, 1.0 V (RMS not specified); 25°C ambient

p. 3

0.22 µH
NOMINAL
±20%; 1 MHz, 0.1 Vrms, 0 Adc; 25°C

p. 1

Different conditions
DCR, typical5.0 mΩ
TYP
25°C reference ambient; measurement instrument not stated

p. 3

5.81 mΩ
TYP
25°C; micro-ohmmeter

p. 1

Different conditions
DCR, maximum5.6 mΩ
MAX
25°C reference ambient; measurement instrument not stated

p. 3

6.40 mΩ
MAX
25°C; micro-ohmmeter

p. 1

Different conditions
Heating-current reference12.0 A
TYP
Idc TYP column; approximate 40°C rise from 25°C ambient

p. 3

16.8 A
NOT_STATED
Irms at 40°C rise from 25°C ambient; reference only, not an absolute maximum

p. 1

Different conditions
MAZO heating current, printed MAX column10.0 A
MAX
Printed MAX label retained; interpretation requires manufacturer clarification

p. 3

Unknown

No corresponding MAX-column designation; do not relabel Coilcraft Irms as an absolute maximum

Insufficient evidence
Saturation-current reference18.5 A
TYP
Isat TYP column; approximate 30% L0 drop; 25°C reference ambient

p. 3

18.7 A
TYP
30% inductance drop from no-current value; 25°C

p. 1

Not assessed
MAZO saturation current, printed MAX column17.5 A
MAX
Printed MAX label retained; interpretation requires manufacturer clarification

p. 3

Unknown

No corresponding MAX-column designation in this table

Insufficient evidence
Listed voltage40 V
MAX
Rated Voltage MAX column

p. 3

60 V
NOT_STATED
Operating voltage; capability varies by part number (footnote 7)

p. 1

Different conditions
Maximum total part temperature125 °C
MAX
Ambient plus temperature rise; verify worst-case application

p. 3

165 °C
MAX
Ambient plus temperature rise; derating applies

p. 1

Not assessed
Footprint interchangeabilityUnknown

Requires comparing actual PCB and recommended land drawing; not established

Unknown

Requires comparing actual PCB and recommended land drawing; not established

Insufficient evidence

Interchangeability has not been established. The nominal inductance matches, but measurement voltage, thermal limits, current conventions and recommended lands differ. MAZO MAX-column current labels are retained as printed and require manufacturer clarification. No unrestricted replacement, application test or stock claim is made.

Original sources

MAZO VCMA-0420 shielded power inductors

Kun Shan MAZO tech Co., Ltd. VCMA-0420 · A4 · 2025-11-26 · EN

Cited pages: p. 2p. 3p. 4

Archive details

Archived: 2026-10-18 · 10 pages · 1195.2 KiB

SHA-256: 96d67552781bed638e5e678e37cb4eec366ee855e832c029d61e967a9cca831c

Coilcraft XAL40xx shielded power inductors

Coilcraft 806 · 02/25/26 · 2026-02-25 · EN

Cited pages: p. 1p. 4

Archive details

Archived: 2026-10-18 · 4 pages · 205.4 KiB

SHA-256: b26cf975bd56a807173b05665bddd49ed49323400330eb8f6fa63e24ff6d7d15

Parts
Catalog parts in this guide

Replies (0)

No replies yet.

Can't find this part? We'll source it

Send us the part number and quantity. An MST engineer will source it, check that it fits your application, and reply with a quote.