MAZO 1.5 µH shielded power inductor, Idc 4.8 A typ. – Alternative to Bourns SRP4020TA-1R5M
- Inductance
- 1.5 µH
- Isat
- 6.5 A
- Idc
- 4.8 A
- DCR max
- 30 mΩ
- Brand
- MAZO
- Series
- VCMA-0420
- Size
- 4.75 × 4.45 × 2 mm
- Category
- MAZO power inductors
- Related applications
- Automotive / OBC
- Features
- AEC-Q200Magnetic shieldRoHSHalogen free
- Stock
- Factory stock

Applications and industries
Industries: Automotive · AEC-Q200 qualified
Manufacturer-listed applications: Automotive applications (datasheet); ADAS, cockpit, powertrain, body and central domain controllers (MAZO application areas)
MST engineering note — typical circuits: 12 V battery buck to 5 V / 3.3 V / core rails, SoC and ADAS processor point-of-load, LED driver and SEPIC / buck-boost stages. Small footprint for low-current rails and space-limited modules; check the 40 V rating against your input.
Sources: VCMA-0420 datasheet · MAZO application areas
Selection tips
Selection tips
- Keep the peak current (DC load plus half the ripple) below Isat 6.5 A; Isat is 1.4× the 4.8 A heating-current rating.
- Copper loss at 4.8 A with DCR max 30 mΩ is about 0.69 W (I² × DCR); size copper and airflow for it.
- Use on rails at or below the 40 V rated voltage.
- Operating temperature -55 °C to +125 °C includes self-heating, so ambient plus temperature rise must stay inside it.
- AEC-Q200 is stated on the datasheet, so the part can enter an automotive qualification plan.
Specifications
Datasheet facts
- Recommended land pattern
- Two 2.5 × 1.5 mm pads, 2.2 mm apart, 5.2 mm overall
- Inductance test condition
- 1 MHz, 1.0 V, 25 °C
- Current definitions
- Isat: inductance drops about 30%; Idc: temperature rise about 40 °C
- Soldering
- Reflow per J-STD-020
- Operating temperature (ambient + self-heating)
- -55 ~ +125 °C
- Storage temperature
- -55 ~ +125 °C
- Packaging
- 3000 pieces per reel; tape pocket 4.5±0.1 × 4.8±0.1 × 2.5±0.15 mm
Datasheet VCMA-0420-XXX-M-1A, revision A4, 2025-11-26, page 4
Characteristic curves
Typical curves from the MAZO datasheet, for reference only.
Soldering and packaging
Alternative to these parts
VCMA-0420-1R5-M-1A matches the parts below in footprint class and nominal value. Request a quote.
| Brand | Part number | L | Isat | Irms | DCR max | Size | Footprint | Recommended pads | VCMA-0420-1R5-M-1A vs. this part |
|---|---|---|---|---|---|---|---|---|---|
| Bourns | SRP4020TA-1R5MSRP4020TA | 1.5 µH | 7 A · 20% | 4.5 A · 40 °C | 42 mΩ | 4.45 × 4.06 × 2 mm | Pad-compatible | 2.4 × 1.5 mm, gap 2.2 mmSame as MAZO | Drop-in candidate |
| TDK | SPM4020T-1R5MSPM4020T | 1.5 µH | 5.9 A · 30% | 4.1 A · 40 °C | 46.8 mΩ | 4.4 × 4.1 × 2 mm | Pad-compatible | 2.3 × 1.65 mm, gap 1.65 mmClose to MAZO (0.55 mm off) | Drop-in candidate |
| TDK | SPM4020T-1R5M-LRSPM4020T-LR | 1.5 µH | 6.3 A · 30% | 4.7 A · 40 °C | 40 mΩ | 4.4 × 4.1 × 2 mm | Pad-compatible | 2.3 × 1.65 mm, gap 1.65 mmClose to MAZO (0.55 mm off) | Drop-in candidate |
| Vishay | IHLP1616BZER1R5M01IHLP-1616BZ-01 | 1.5 µH | 6.1 A · 20% | 5.1 A · 40 °C | 46.3 mΩ | 4.06 × 4.45 × 2 mm | Pad-compatible | 2.286 × 1.855 mm, gap 1.93 mmClose to MAZO (0.439 mm off) | Drop-in candidate |
| Coilcraft | XAL4020-152MECXAL4020 | 1.5 µH | 7.1 A · 30% | 7.5 A · 40 °C | 23.6 mΩ | 4 × 4 × 2.1 mm | Same footprint class | 3.4 × 0.98 mm, gap 1.39 mmDiffers from MAZO (1.85 mm off) | Weaker figures |
| Coilcraft | XFL4020-152MECXFL4020 | 1.5 µH | 4.6 A · 30% | 9.1 A · 40 °C | 15.8 mΩ | 4 × 4 × 2.1 mm | Same footprint class | 3.4 × 0.98 mm, gap 1.39 mmDiffers from MAZO (1.85 mm off) | Weaker figures |
| Cyntec | VCHA042A-1R5MS62MVCHA042A MS62M | 1.5 µH | 6.2 A · 30% | 7.3 A · 40 °C | 15.4 mΩ | 4.2 × 4 × 2.1 mm | Same footprint class | 2.286 × 1.855 mm, gap 1.93 mmClose to MAZO (0.439 mm off) | Weaker figures |
| Würth Elektronik | 74438356015WE-MAPI 4020 | 1.5 µH | 10.2 A · 30% | 8.6 A · 40 °C | 19 mΩ | 4.1 × 4.1 × 2.1 mm | Same footprint class | 3.7 × 0.98 mm, gap 1.39 mmDiffers from MAZO (1.85 mm off) | Weaker figures |
| Würth Elektronik | 74439323015WE-XHMI 4020 | 1.5 µH | 8.4 A · 30% | 7.8 A · 40 °C | 18.48 mΩ | 4.3 × 4.3 × 2 mm | Same footprint class | 3.8 × 1.2 mm, gap 1.25 mmDiffers from MAZO (1.55 mm off) | Weaker figures |
What each comparison means (9)
- Bourns SRP4020TA-1R5M: Same inductance, 1.5 µH vs MAZO 1.5 µH. Saturation current 7 A (20% drop) vs MAZO 6.5 A typ. (30% drop), rated on different bases so not directly comparable; heating current 4.5 A (40 °C rise) vs MAZO 4.8 A typ. (40 °C rise). DCR 42 mΩ max vs MAZO 30 mΩ max. Body 4.45 × 4.06 × 2 mm vs MAZO 4.75 × 4.45 × 2 mm. Same land pattern as MAZO (two 2.5 × 1.5 mm pads 2.2 mm apart). Verdict: drop-in candidate (Idc not lower at 40 °C rise, DCR lower, less conduction loss). Request a quote. Both parts are AEC-Q200.
- TDK SPM4020T-1R5M: Same inductance, 1.5 µH vs MAZO 1.5 µH. Saturation current 5.9 A (30% drop) vs MAZO 6.5 A typ. (30% drop); heating current 4.1 A (40 °C rise) vs MAZO 4.8 A typ. (40 °C rise). DCR 46.8 mΩ typ vs MAZO 25 mΩ typ. Body 4.4 × 4.1 × 2 mm vs MAZO 4.75 × 4.45 × 2 mm. Land pattern close to MAZO's: two 2.3 × 1.65 mm pads 1.65 mm apart vs MAZO two 2.5 × 1.5 mm pads 2.2 mm apart (gap differs by 0.55 mm). Verdict: drop-in candidate (MAZO Isat not lower, Idc not lower at 40 °C rise, DCR lower, less conduction loss). Request a quote.
- TDK SPM4020T-1R5M-LR (SPM4020T-LR): Same inductance, 1.5 µH vs MAZO 1.5 µH. Saturation current 6.3 A (30% drop) vs MAZO 6.5 A typ. (30% drop); heating current 4.7 A (40 °C rise) vs MAZO 4.8 A typ. (40 °C rise). DCR 40 mΩ max vs MAZO 30 mΩ max. Body 4.4 × 4.1 × 2 mm vs MAZO 4.75 × 4.45 × 2 mm. Land pattern close to MAZO's: two 2.3 × 1.65 mm pads 1.65 mm apart vs MAZO two 2.5 × 1.5 mm pads 2.2 mm apart (gap differs by 0.55 mm). Verdict: drop-in candidate (MAZO Isat not lower, Idc not lower at 40 °C rise, DCR lower, less conduction loss). Request a quote.
- Vishay IHLP1616BZER1R5M01 (IHLP-1616BZ-01): Same inductance, 1.5 µH vs MAZO 1.5 µH. Saturation current 6.1 A (20% drop) vs MAZO 6.5 A typ. (30% drop), rated on different bases so not directly comparable; heating current 5.1 A (40 °C rise) vs MAZO 4.8 A typ. (40 °C rise). DCR 46.3 mΩ max vs MAZO 30 mΩ max. Body 4.06 × 4.45 × 2 mm vs MAZO 4.75 × 4.45 × 2 mm. Land pattern close to MAZO's: two 2.286 × 1.855 mm pads 1.93 mm apart vs MAZO two 2.5 × 1.5 mm pads 2.2 mm apart (overall span differs by 0.439 mm). Verdict: drop-in candidate (Idc about 6% lower at 40 °C rise, DCR lower, less conduction loss). Request a quote.
- Coilcraft XAL4020-152MEC: Same inductance, 1.5 µH vs MAZO 1.5 µH. Saturation current 7.1 A (30% drop) vs MAZO 6.5 A typ. (30% drop); heating current 7.5 A (40 °C rise) vs MAZO 4.8 A typ. (40 °C rise). DCR 23.6 mΩ max vs MAZO 30 mΩ max. Body 4 × 4 × 2.1 mm vs MAZO 4.75 × 4.45 × 2 mm, MAZO 0.1 mm lower. Land pattern differs from MAZO's: two 3.4 × 0.98 mm pads 1.39 mm apart vs MAZO two 2.5 × 1.5 mm pads 2.2 mm apart (overall span differs by 1.85 mm). Verdict: MAZO figures are weaker, consider only with ample margin (MAZO Isat about 8% lower, Idc about 36% lower at 40 °C rise, DCR slightly higher). Request a quote. Both parts are AEC-Q200.
- Coilcraft XFL4020-152MEC: Same inductance, 1.5 µH vs MAZO 1.5 µH. Saturation current 4.6 A (30% drop) vs MAZO 6.5 A typ. (30% drop); heating current 9.1 A (40 °C rise) vs MAZO 4.8 A typ. (40 °C rise). DCR 15.8 mΩ max vs MAZO 30 mΩ max. Body 4 × 4 × 2.1 mm vs MAZO 4.75 × 4.45 × 2 mm, MAZO 0.1 mm lower. Land pattern differs from MAZO's: two 3.4 × 0.98 mm pads 1.39 mm apart vs MAZO two 2.5 × 1.5 mm pads 2.2 mm apart (overall span differs by 1.85 mm). Verdict: MAZO figures are weaker, consider only with ample margin (MAZO Isat not lower, Idc about 47% lower at 40 °C rise, DCR slightly higher). Request a quote. Both parts are AEC-Q200.
- Cyntec VCHA042A-1R5MS62M (VCHA042A MS62M): Same inductance, 1.5 µH vs MAZO 1.5 µH. Saturation current 6.2 A (30% drop) vs MAZO 6.5 A typ. (30% drop); heating current 7.3 A (40 °C rise) vs MAZO 4.8 A typ. (40 °C rise). DCR 15.4 mΩ max vs MAZO 30 mΩ max. Body 4.2 × 4 × 2.1 mm vs MAZO 4.75 × 4.45 × 2 mm, MAZO 0.1 mm lower. Land pattern close to MAZO's: two 2.286 × 1.855 mm pads 1.93 mm apart vs MAZO two 2.5 × 1.5 mm pads 2.2 mm apart (overall span differs by 0.439 mm). Verdict: MAZO figures are weaker, consider only with ample margin (MAZO Isat not lower, Idc about 34% lower at 40 °C rise, DCR slightly higher). Request a quote. Both parts are AEC-Q200.
- Würth Elektronik 74438356015 (WE-MAPI 4020): Same inductance, 1.5 µH vs MAZO 1.5 µH. Saturation current 10.2 A (30% drop) vs MAZO 6.5 A typ. (30% drop); heating current 8.6 A (40 °C rise) vs MAZO 4.8 A typ. (40 °C rise). DCR 19 mΩ max vs MAZO 30 mΩ max. Body 4.1 × 4.1 × 2.1 mm vs MAZO 4.75 × 4.45 × 2 mm, MAZO 0.1 mm lower. Land pattern differs from MAZO's: two 3.7 × 0.98 mm pads 1.39 mm apart vs MAZO two 2.5 × 1.5 mm pads 2.2 mm apart (overall span differs by 1.85 mm). Verdict: MAZO figures are weaker, consider only with ample margin (MAZO Isat about 36% lower, Idc about 44% lower at 40 °C rise, DCR slightly higher). Request a quote. Both parts are AEC-Q200.
- Würth Elektronik 74439323015 (WE-XHMI 4020): Same inductance, 1.5 µH vs MAZO 1.5 µH. Saturation current 8.4 A (30% drop) vs MAZO 6.5 A typ. (30% drop); heating current 7.8 A (40 °C rise) vs MAZO 4.8 A typ. (40 °C rise). DCR 18.48 mΩ max vs MAZO 30 mΩ max. Body 4.3 × 4.3 × 2 mm vs MAZO 4.75 × 4.45 × 2 mm. Land pattern differs from MAZO's: two 3.8 × 1.2 mm pads 1.25 mm apart vs MAZO two 2.5 × 1.5 mm pads 2.2 mm apart (overall span differs by 1.55 mm). Verdict: MAZO figures are weaker, consider only with ample margin (MAZO Isat about 23% lower, Idc about 38% lower at 40 °C rise, DCR slightly higher). Request a quote. Both parts are AEC-Q200.
How the figures are compared
Isat and Irms follow each datasheet's own definition, shown after the figure. MAZO figures are typical values from its spec table.
Recommended pads: pad width × pad length, then the gap between the two pads, from each datasheet, compared with MAZO's.
Engineering guides for this part
More parts in this category
- MAZO VCMU / XAL / XGL T-core power inductor series selection guide
- MAZO VMCI 12V/1V AI coupled inductor 85 nH 55 A series selection guide
- MAZO VMSC 85 nH 55 A AI buck inductor series selection guide
- MAZO 10 µH 40 V shielded power inductor
- MAZO 1 µH 40 V 6.5 A shielded power inductor
- MAZO VCMA-0420 1.2 µH 40 V shielded power inductor
- MAZO 2.2 µH 40 V shielded power inductor
- MAZO 3.3 µH 4.5 A shielded power inductor
- MAZO 4.7 µH 40 V shielded power inductor
- MAZO 6.8 µH 40 V shielded power inductor, 4.75 × 4.45 × 2.0 mm
- MAZO 0.1 µH 15 A shielded power inductor
- MAZO 0.22 µH 40 V 12 A shielded power inductor
Same footprint, other values
Same 4.75 × 4.45 mm body, by inductance.
| Part number | L | Isat | Idc | DCR max | Height | Unit price |
|---|---|---|---|---|---|---|
| VCMA-0420-R10-M-1A | 0.1 µH | 22 A | 15 A | 4 mΩ | 2 mm | $0.21 |
| VCMA-0420-R22-M-1A | 0.22 µH | 18.5 A | 12 A | 5.6 mΩ | 2 mm | $0.21 |
| VCMA-0420-R33-M-1A | 0.33 µH | 16 A | 10 A | 8 mΩ | 2 mm | $0.21 |
| VCMA-0420-R47-M-1A | 0.47 µH | 12 A | 8.5 A | 12 mΩ | 2 mm | $0.22 |
| VCMA-0420-R56-M-1A | 0.56 µH | 10.5 A | 8 A | 13 mΩ | 2 mm | $0.28 |
| VCMA-0420-R68-M-1A | 0.68 µH | 9 A | 7.5 A | 14 mΩ | 2 mm | $0.28 |
| VCMA-0420-1R0-M-1A | 1 µH | 7.5 A | 6.5 A | 24 mΩ | 2 mm | $0.28 |
| VCMA-0420-1R2-M-1A | 1.2 µH | 7 A | 6.2 A | 27 mΩ | 2 mm | $0.28 |
| VCMA-0420-2R2-M-1A | 2.2 µH | 5.5 A | 4.2 A | 50 mΩ | 2 mm | $0.21 |
| VCMA-0420-3R3-M-1A | 3.3 µH | 4.5 A | 3.3 A | 82 mΩ | 2 mm | $0.23 |
| VCMA-0420-4R7-M-1A | 4.7 µH | 3.3 A | 2.5 A | 105 mΩ | 2 mm | $0.33 |
| VCMA-0420-6R8-M-1A | 6.8 µH | 2.6 A | 2 A | 185 mΩ | 2 mm | $0.36 |
Same value, other sizes
Smallest first. A larger body usually carries more current; the pads differ.
| Part number | L | Isat | Idc | DCR max | Body | Unit price |
|---|---|---|---|---|---|---|
| VCMA-0530-1R5-M-1A | 1.5 µH | 10 A | 8 A | 18 mΩ | 5.7 × 5.4 × 3 mm | $0.30 |
| VCMA-0630-1R5-M-1A | 1.5 µH | 14.5 A | 12 A | 11 mΩ | 7.3 × 6.8 × 3 mm | $0.23 |
| VCMA-1040-1R5-M-1A | 1.5 µH | 27 A | 17 A | 3.8 mΩ | 11.5 × 10.3 × 4 mm | $0.52 |
| VCMA-1350-1R5-M-1A | 1.5 µH | 39 A | 23 A | 3.1 mΩ | 13.8 × 12.9 × 5 mm | $0.75 |
| VCMA-1365-1R5-M-1A | 1.5 µH | 40 A | 35 A | 2.5 mΩ | 13.8 × 12.9 × 6.5 mm | $0.79 |
Buy
| Quantity | Unit price | Extended |
|---|---|---|
| 5–49 | $0.28 | $1.40 |
| 50–149 | $0.21 | $10.50 |
| 150–499 | $0.163 | $24.45 |
| 500–2999 | $0.134 | $67.00 |
- Minimum order
- 5 pieces
- Order multiple
- 1 piece
- Availability
- Factory stock
- Dispatch preparation
- 2 days
Dispatch preparation and shipping transit are separate. Arrival is estimated; the confirmed route and shipment tracking determine delivery.
- Standard full-reel quantity
- 3000 pieces
- Packed as
- Cut tape · 5 pieces
- Cut-tape fee
- None
- Online order limit
- 2999 pieces
Packaging and handling charges are shown in the cart. Shipping, duties and tax are confirmed separately.
Add this quantity to your cart to review order charges and the available payment steps. Sign in if prompted.
Can't find it? We'll source it — and check it fits.
Not sure it fits your tool/process? Ask an engineer to check
An MST engineer will review your requirement and reply to help with sourcing and compatibility.
Selection and use
How to select
Choosing inductance
L ≈ (Vin − Vout) × Vout ÷ (Vin × fsw × ΔI), with ΔI at 20–40% of the output current. The series covers 0.1–10 µH in one body, so changing the value needs no new layout.
Saturation current Isat
the current at which inductance falls about 30%; keep the peak current below it.
Heating current Idc
the current that raises the part about 40 °C above a 25 °C ambient; ambient plus rise stays within 125 °C.
DC resistance
sets the conduction loss. Typical 3.5–245 mΩ across the series; use the maximum for loss budgets.
Rated voltage
40 V maximum; check it against the input voltage.
Height
Max 2.0 mm. For more current, VCMA-0530 or VCMA-0630.
Industry and product applications
VCMA-0420-1R5-M-1A is a VCMA-0420 series part for evaluation in automotive electronics.
Manufacturer-listed series applications
Automotive applications.
MAZO datasheet: VCMA-0420-XXX-M-1A, revision A4, 2025-11-26 — applications on page 1
Circuit applications to evaluate
These are series applications and engineering evaluation examples. Select VCMA-0420-1R5-M-1A against the required inductance, peak and RMS current, switching frequency, temperature rise and PCB footprint. Inclusion here does not establish suitability for a particular design or qualification of the finished product.
Frequently asked questions
What are the key specifications of VCMA-0420-1R5-M-1A?
VCMA-0420-1R5-M-1A: Brand: MAZO / Mazotech; Series: VCMA-0420; Inductance L0: 1.5 µH ±20% (1 MHz, 1.0 V); DCR typ.: 25 mΩ; DCR max.: 30 mΩ; Heating current Idc typ.: 4.8 A. Full values are in the specifications table above.
Which parts can VCMA-0420-1R5-M-1A be evaluated as an alternative to?
VCMA-0420-1R5-M-1A is listed as an alternative to Bourns SRP4020TA-1R5M, TDK SPM4020T-1R5M, TDK SPM4020T-1R5M-LR, Vishay IHLP1616BZER1R5M01, Coilcraft XAL4020-152MEC, Coilcraft XFL4020-152MEC (same footprint class and nominal value). Request a quote with the RFQ form on this page.
What does VCMA-0420-1R5-M-1A cost?
VCMA-0420-1R5-M-1A is US$0.28 per piece, minimum order 5 pieces, with DHL shipping quoted by destination.
Can MST source a part number that is not listed?
Yes. Send the exact part number and quantity through the RFQ form and MST sources it and replies with a quote.