MST
RFQ cartCart
VCMA-0420-R10-M-1A

MAZO 0.1 µH shielded power inductor, Idc 15 A typ.

Inductance
0.1 µH
Isat
22 A
Idc
15 A
DCR max
4 mΩ
Brand
MAZO
Series
VCMA-0420
Size
4.75 × 4.45 × 2 mm
Related applications
Automotive / OBC
Features
AEC-Q200Magnetic shieldRoHSHalogen free
Stock
Factory stock

Applications and industries

Industries: Automotive · AEC-Q200 qualified

Manufacturer-listed applications: Automotive applications (datasheet); ADAS, cockpit, powertrain, body and central domain controllers (MAZO application areas)

MST engineering note — typical circuits: 12 V battery buck to 5 V / 3.3 V / core rails, SoC and ADAS processor point-of-load, LED driver and SEPIC / buck-boost stages. Small footprint for low-current rails and space-limited modules; check the 40 V rating against your input.

Sources: VCMA-0420 datasheet · MAZO application areas

Selection tips

Selection tips

  • Keep the peak current (DC load plus half the ripple) below Isat 22 A; Isat is 1.5× the 15 A heating-current rating.
  • Copper loss at 15 A with DCR max 4 mΩ is about 0.9 W (I² × DCR); size copper and airflow for it.
  • Use on rails at or below the 40 V rated voltage.
  • Operating temperature -55 °C to +125 °C includes self-heating, so ambient plus temperature rise must stay inside it.
  • AEC-Q200 is stated on the datasheet, so the part can enter an automotive qualification plan.
MST engineering note, computed from the published specifications above. Request a quote.

Specifications

BrandMAZO / Mazotech
SeriesVCMA-0420
Inductance L00.1 µH ±20% (1 MHz, 1.0 V)
DCR typ.3.5 mΩ
DCR max.4 mΩ
Heating current Idc typ.15 A
Heating current Idc max.12 A
Saturation current Isat typ.22 A
Saturation current Isat max.20 A
Rated voltage max.40 V
Package4.75 × 4.45 × 2.0 mm max
Operating temperature-55 °C to +125 °C (ambient plus self-temperature rise)
Magnetic constructionMagnetically shielded, low EMI
QualificationAEC-Q200 qualified; RoHS compliant; halogen free
ApplicationsAutomotive applications

Datasheet facts

2.22.51.55.2
Recommended land pattern (mm)
Recommended land pattern
Two 2.5 × 1.5 mm pads, 2.2 mm apart, 5.2 mm overall
Inductance test condition
1 MHz, 1.0 V, 25 °C
Current definitions
Isat: inductance drops about 30%; Idc: temperature rise about 40 °C
Soldering
Reflow per J-STD-020
Operating temperature (ambient + self-heating)
-55 ~ +125 °C
Storage temperature
-55 ~ +125 °C
Packaging
3000 pieces per reel; tape pocket 4.5±0.1 × 4.8±0.1 × 2.5±0.15 mm

Datasheet VCMA-0420-XXX-M-1A, revision A4, 2025-11-26, page 4

Characteristic curves

Inductance vs DC biasCSV
00.0250.050.0750.10.125010203040Isat 22 ADC current (A)Inductance (µH)
Temperature rise vs currentCSV
02550751001250102030Idc 15 ADC current (A)Temperature rise (°C)

Typical curves from the MAZO datasheet, for reference only.

Soldering and packaging

Alternative to these parts

VCMA-0420-R10-M-1A matches the parts below in footprint class and nominal value. Request a quote.

BrandPart numberLIsatIrmsDCR maxSizeFootprintRecommended padsVCMA-0420-R10-M-1A vs. this part
BournsSRP4020TA-R10YSRP4020TA0.1 µH35 A · 20%12 A · 40 °C4 mΩ4.45 × 4.06 × 2 mmPad-compatible2.4 × 1.5 mm, gap 2.2 mmSame as MAZOWeaker figures
VishayIHLP1616BZERR10M01IHLP-1616BZ-010.1 µH35 A · 20%16 A · 40 °C5 mΩ4.06 × 4.45 × 2 mmPad-compatible2.286 × 1.855 mm, gap 1.93 mmClose to MAZO (0.439 mm off)Weaker figures
CyntecVCHA042A-R10MS62MVCHA042A MS62M0.1 µH25 A · 30%21 A · 40 °C2.28 mΩ4.2 × 4 × 2.1 mmSame footprint class2.286 × 1.855 mm, gap 1.93 mmClose to MAZO (0.439 mm off)Weaker figures
What each comparison means (3)
  1. Bourns SRP4020TA-R10Y: Same inductance, 0.1 µH vs MAZO 0.1 µH. Saturation current 35 A (20% drop) vs MAZO 22 A typ. (30% drop), rated on different bases so not directly comparable; heating current 12 A (40 °C rise) vs MAZO 15 A typ. (40 °C rise). DCR 4 mΩ max vs MAZO 4 mΩ max. Body 4.45 × 4.06 × 2 mm vs MAZO 4.75 × 4.45 × 2 mm. Same land pattern as MAZO (two 2.5 × 1.5 mm pads 2.2 mm apart). Verdict: MAZO figures are weaker, consider only with ample margin (Idc not lower at 40 °C rise, DCR equal). Request a quote. Both parts are AEC-Q200.
  2. Vishay IHLP1616BZERR10M01 (IHLP-1616BZ-01): Same inductance, 0.1 µH vs MAZO 0.1 µH. Saturation current 35 A (20% drop) vs MAZO 22 A typ. (30% drop), rated on different bases so not directly comparable; heating current 16 A (40 °C rise) vs MAZO 15 A typ. (40 °C rise). DCR 5 mΩ max vs MAZO 4 mΩ max. Body 4.06 × 4.45 × 2 mm vs MAZO 4.75 × 4.45 × 2 mm. Land pattern close to MAZO's: two 2.286 × 1.855 mm pads 1.93 mm apart vs MAZO two 2.5 × 1.5 mm pads 2.2 mm apart (overall span differs by 0.439 mm). Verdict: MAZO figures are weaker, consider only with ample margin (Idc about 6% lower at 40 °C rise, DCR lower, less conduction loss). Request a quote.
  3. Cyntec VCHA042A-R10MS62M (VCHA042A MS62M): Same inductance, 0.1 µH vs MAZO 0.1 µH. Saturation current 25 A (30% drop) vs MAZO 22 A typ. (30% drop); heating current 21 A (40 °C rise) vs MAZO 15 A typ. (40 °C rise). DCR 2.28 mΩ max vs MAZO 4 mΩ max. Body 4.2 × 4 × 2.1 mm vs MAZO 4.75 × 4.45 × 2 mm, MAZO 0.1 mm lower. Land pattern close to MAZO's: two 2.286 × 1.855 mm pads 1.93 mm apart vs MAZO two 2.5 × 1.5 mm pads 2.2 mm apart (overall span differs by 0.439 mm). Verdict: MAZO figures are weaker, consider only with ample margin (MAZO Isat about 12% lower, Idc about 29% lower at 40 °C rise, DCR slightly higher). Request a quote. Both parts are AEC-Q200.
How the figures are compared

Isat and Irms follow each datasheet's own definition, shown after the figure. MAZO figures are typical values from its spec table.

Recommended pads: pad width × pad length, then the gap between the two pads, from each datasheet, compared with MAZO's.

Engineering guides for this part

More parts in this category

Same footprint, other values

Same 4.75 × 4.45 mm body, by inductance.

Part numberLIsatIdcDCR maxHeightUnit price
VCMA-0420-R22-M-1A0.22 µH18.5 A12 A5.6 mΩ2 mm$0.21
VCMA-0420-R33-M-1A0.33 µH16 A10 A8 mΩ2 mm$0.21
VCMA-0420-R47-M-1A0.47 µH12 A8.5 A12 mΩ2 mm$0.22
VCMA-0420-R56-M-1A0.56 µH10.5 A8 A13 mΩ2 mm$0.28
VCMA-0420-R68-M-1A0.68 µH9 A7.5 A14 mΩ2 mm$0.28
VCMA-0420-1R0-M-1A1 µH7.5 A6.5 A24 mΩ2 mm$0.28
VCMA-0420-1R2-M-1A1.2 µH7 A6.2 A27 mΩ2 mm$0.28
VCMA-0420-1R5-M-1A1.5 µH6.5 A4.8 A30 mΩ2 mm$0.28
VCMA-0420-2R2-M-1A2.2 µH5.5 A4.2 A50 mΩ2 mm$0.21
VCMA-0420-3R3-M-1A3.3 µH4.5 A3.3 A82 mΩ2 mm$0.23
VCMA-0420-4R7-M-1A4.7 µH3.3 A2.5 A105 mΩ2 mm$0.33
VCMA-0420-6R8-M-1A6.8 µH2.6 A2 A185 mΩ2 mm$0.36

Buy

Unit price · USD / piece$0.21For 5 pieces
Quantity pricingSelect a tier to set the quantity.
QuantityUnit priceExtended
5–49$0.21$1.05
50–149$0.16$8.00
150–499$0.121$18.15
500–2999$0.1$50.00
Merchandise subtotal$1.05Item amount only; excludes packaging, handling, shipping, duties and tax. Packaging and handling charges are shown in the cart. Shipping, duties and tax are confirmed separately.
Minimum order
5 pieces
Order multiple
1 piece
Availability
Factory stock
Dispatch preparation
2 days
Ships from ChinaShipping: DHL ExpressChoose a delivery country to see the transit estimate.

Dispatch preparation and shipping transit are separate. Arrival is estimated; the confirmed route and shipment tracking determine delivery.

Minimum order: 5; order in multiples of 1.
PackagingFor the selected quantity
Standard full-reel quantity
3000 pieces
Packed as
Cut tape · 5 pieces
Cut-tape fee
None
Online order limit
2999 pieces

Packaging and handling charges are shown in the cart. Shipping, duties and tax are confirmed separately.

Add this quantity to your cart to review order charges and the available payment steps. Sign in if prompted.

Can't find it? We'll source it — and check it fits.

Not sure it fits your tool/process? Ask an engineer to check

An MST engineer will review your requirement and reply to help with sourcing and compatibility.

Request sourcing & fit check

Selection and use

How to select

Choosing inductance

L ≈ (Vin − Vout) × Vout ÷ (Vin × fsw × ΔI), with ΔI at 20–40% of the output current. The series covers 0.1–10 µH in one body, so changing the value needs no new layout.

Saturation current Isat

the current at which inductance falls about 30%; keep the peak current below it.

Heating current Idc

the current that raises the part about 40 °C above a 25 °C ambient; ambient plus rise stays within 125 °C.

DC resistance

sets the conduction loss. Typical 3.5–245 mΩ across the series; use the maximum for loss budgets.

Rated voltage

40 V maximum; check it against the input voltage.

Height

Max 2.0 mm. For more current, VCMA-0530 or VCMA-0630.

Industry and product applications

VCMA-0420-R10-M-1A is a VCMA-0420 series part for evaluation in automotive electronics.

Manufacturer-listed series applications

Automotive applications.

MAZO datasheet: VCMA-0420-XXX-M-1A, revision A4, 2025-11-26 — applications on page 1

Circuit applications to evaluate

  • Sensor and camera module supplies
  • Point-of-load bucks next to MCUs
  • LED drivers and backlight
  • BMS and on-board charger auxiliary supplies

These are series applications and engineering evaluation examples. Select VCMA-0420-R10-M-1A against the required inductance, peak and RMS current, switching frequency, temperature rise and PCB footprint. Inclusion here does not establish suitability for a particular design or qualification of the finished product.

Frequently asked questions

What are the key specifications of VCMA-0420-R10-M-1A?

VCMA-0420-R10-M-1A: Brand: MAZO / Mazotech; Series: VCMA-0420; Inductance L0: 0.1 µH ±20% (1 MHz, 1.0 V); DCR typ.: 3.5 mΩ; DCR max.: 4 mΩ; Heating current Idc typ.: 15 A. Full values are in the specifications table above.

Which parts can VCMA-0420-R10-M-1A be evaluated as an alternative to?

VCMA-0420-R10-M-1A is listed as an alternative to Bourns SRP4020TA-R10Y, Vishay IHLP1616BZERR10M01, Cyntec VCHA042A-R10MS62M (same footprint class and nominal value). Request a quote with the RFQ form on this page.

What does VCMA-0420-R10-M-1A cost?

VCMA-0420-R10-M-1A is US$0.21 per piece, minimum order 5 pieces, with DHL shipping quoted by destination.

Can MST source a part number that is not listed?

Yes. Send the exact part number and quantity through the RFQ form and MST sources it and replies with a quote.