MST
RFQ cartCart
VCMA-0630-R56-M-1A

MAZO 0.56 µH shielded power inductor, Idc 18 A typ. – Alternative to TDK SPM6530T-R56M

Inductance
0.56 µH
Isat
19 A
Idc
18 A
DCR max
4.5 mΩ
Brand
MAZO
Series
VCMA-0630
Size
7.3 × 6.8 × 3 mm
Related applications
Automotive / OBC
Features
AEC-Q200Magnetic shieldRoHSHalogen free
Stock
Factory stock

Applications and industries

Industries: Automotive · AEC-Q200 qualified

Manufacturer-listed applications: Automotive applications (datasheet); ADAS, cockpit, powertrain, body and central domain controllers (MAZO application areas)

MST engineering note — typical circuits: 12 V battery buck to 5 V / 3.3 V / core rails, SoC and ADAS processor point-of-load, LED driver and SEPIC / buck-boost stages. Mid-current rails.

Sources: VCMA-0630 datasheet · MAZO application areas

Selection tips

Selection tips

  • Keep the peak current (DC load plus half the ripple) below Isat 19 A; Isat is 1.1× the 18 A heating-current rating.
  • Copper loss at 18 A with DCR max 4.5 mΩ is about 1.46 W (I² × DCR); size copper and airflow for it.
  • Use on rails at or below the 75 V rated voltage.
  • Operating temperature -55 °C to +125 °C includes self-heating, so ambient plus temperature rise must stay inside it.
  • AEC-Q200 is stated on the datasheet, so the part can enter an automotive qualification plan.
MST engineering note, computed from the published specifications above. Request a quote.

Specifications

BrandMAZO / Mazotech
SeriesVCMA-0630
Inductance L00.56 µH ±20% (1 MHz, 1.0 V)
DCR typ.3.9 mΩ
DCR max.4.5 mΩ
Heating current Idc typ.18 A
Heating current Idc max.17 A
Saturation current Isat typ.19 A
Saturation current Isat max.18 A
Rated voltage max.75 V
Package7.3 × 6.8 × 3.0 mm max
Operating temperature-55 °C to +125 °C (ambient plus self-temperature rise)
Magnetic constructionMagnetically shielded, low EMI
QualificationAEC-Q200 qualified; RoHS compliant; halogen free
Packaging1500 pieces/reel
ApplicationsAutomotive applications

Datasheet facts

3.73.52.358.4
Recommended land pattern (mm)
Recommended land pattern
Two 3.5 × 2.35 mm pads, 3.7 mm apart, 8.4 mm overall
Inductance test condition
1 MHz, 1.0 V, 25 °C
Current definitions
Isat: inductance drops about 30%; Idc: temperature rise about 40 °C
Soldering
Reflow per J-STD-020
Operating temperature (ambient + self-heating)
-55 ~ +125 °C
Storage temperature
-55 ~ +125 °C
Packaging
1500 pieces per reel; tape pocket 7.2±0.10 × 7.5±0.10 × 3.6±0.15 mm

Datasheet VCMA-0630-XXX-M-1A, revision A2, 2025-11-26, page 4

Characteristic curves

Inductance vs DC biasCSV
00.20.40.60102030Isat 19 ADC current (A)Inductance (µH)
Temperature rise vs currentCSV
02550751001250102030Idc 18 ADC current (A)Temperature rise (°C)

Typical curves from the MAZO datasheet, for reference only.

Soldering and packaging

Alternative to these parts

VCMA-0630-R56-M-1A matches the parts below in footprint class and nominal value. Request a quote.

BrandPart numberLIsatIrmsDCR maxSizeFootprintRecommended padsVCMA-0630-R56-M-1A vs. this part
TDKSPM6530T-R56MSPM6530T0.56 µH20.5 A · 20%20 A · 40 °C3.63 mΩ7.1 × 6.5 × 3 mmSame footprint class3.4 × 1.85 mm, gap 3.7 mmDiffers from MAZO (1 mm off)With margin; check the pads
BournsSRP6030CA-R56MSRP6030CA0.56 µH29 A · 30%22 A · 40 °C3.31 mΩ6.6 × 6.4 × 2.8 mmSame footprint class5.6 × 1.55 mm, gap 2.5 mmDiffers from MAZO (2.8 mm off)Weaker figures
BournsSRP6530A-R56MSRP6530A0.56 µH28 A · 30%18 A · 40 °C5.5 mΩ7.1 × 6.6 × 3 mmSame footprint class3.4 × 1.85 mm, gap 3.7 mmDiffers from MAZO (1 mm off)Weaker figures
CoilcraftXAL6030-561MECXAL60300.56 µH29 A · 30%22 A · 40 °C3.31 mΩ6.36 × 6.56 × 3.1 mmSame footprint class5.5 × 1.43 mm, gap 2.61 mmDiffers from MAZO (2.93 mm off)Weaker figures
Würth Elektronik744393440056WE-XHMI 60300.56 µH30.8 A · 30%16 A · 40 °C3.19 mΩ6.65 × 6.45 × 3 mmSame footprint class5.5 × 1.45 mm, gap 2.55 mmDiffers from MAZO (2.95 mm off)Weaker figures
What each comparison means (5)
  1. TDK SPM6530T-R56M: Same inductance, 0.56 µH vs MAZO 0.56 µH. Saturation current 20.5 A (20% drop) vs MAZO 19 A typ. (30% drop), rated on different bases so not directly comparable; heating current 20 A (40 °C rise) vs MAZO 18 A typ. (40 °C rise). DCR 3.63 mΩ max vs MAZO 4.5 mΩ max. Body 7.1 × 6.5 × 3 mm vs MAZO 7.3 × 6.8 × 3 mm. Land pattern differs from MAZO's: two 3.4 × 1.85 mm pads 3.7 mm apart vs MAZO two 3.5 × 2.35 mm pads 3.7 mm apart (overall span differs by 1 mm). Verdict: replaceable with design margin, pads need checking (Idc about 10% lower at 40 °C rise, DCR slightly higher). Request a quote.
  2. Bourns SRP6030CA-R56M: Same inductance, 0.56 µH vs MAZO 0.56 µH. Saturation current 29 A (30% drop) vs MAZO 19 A typ. (30% drop); heating current 22 A (40 °C rise) vs MAZO 18 A typ. (40 °C rise). DCR 3.31 mΩ max vs MAZO 4.5 mΩ max. Body 6.6 × 6.4 × 2.8 mm vs MAZO 7.3 × 6.8 × 3 mm, MAZO 0.2 mm taller. Land pattern differs from MAZO's: two 5.6 × 1.55 mm pads 2.5 mm apart vs MAZO two 3.5 × 2.35 mm pads 3.7 mm apart (overall span differs by 2.8 mm). Verdict: MAZO figures are weaker, consider only with ample margin (MAZO Isat about 34% lower, Idc about 18% lower at 40 °C rise, DCR slightly higher). Request a quote. Both parts are AEC-Q200.
  3. Bourns SRP6530A-R56M: Same inductance, 0.56 µH vs MAZO 0.56 µH. Saturation current 28 A (30% drop) vs MAZO 19 A typ. (30% drop); heating current 18 A (40 °C rise) vs MAZO 18 A typ. (40 °C rise). DCR 5.5 mΩ max vs MAZO 4.5 mΩ max. Body 7.1 × 6.6 × 3 mm vs MAZO 7.3 × 6.8 × 3 mm. Land pattern differs from MAZO's: two 3.4 × 1.85 mm pads 3.7 mm apart vs MAZO two 3.5 × 2.35 mm pads 3.7 mm apart (overall span differs by 1 mm). Verdict: MAZO figures are weaker, consider only with ample margin (MAZO Isat about 32% lower, Idc not lower at 40 °C rise, DCR lower, less conduction loss). Request a quote. Both parts are AEC-Q200.
  4. Coilcraft XAL6030-561MEC: Same inductance, 0.56 µH vs MAZO 0.56 µH. Saturation current 29 A (30% drop) vs MAZO 19 A typ. (30% drop); heating current 22 A (40 °C rise) vs MAZO 18 A typ. (40 °C rise). DCR 3.31 mΩ max vs MAZO 4.5 mΩ max. Body 6.36 × 6.56 × 3.1 mm vs MAZO 7.3 × 6.8 × 3 mm, MAZO 0.1 mm lower. Land pattern differs from MAZO's: two 5.5 × 1.43 mm pads 2.61 mm apart vs MAZO two 3.5 × 2.35 mm pads 3.7 mm apart (overall span differs by 2.93 mm). Verdict: MAZO figures are weaker, consider only with ample margin (MAZO Isat about 34% lower, Idc about 18% lower at 40 °C rise, DCR slightly higher). Request a quote. Both parts are AEC-Q200.
  5. Würth Elektronik 744393440056 (WE-XHMI 6030): Same inductance, 0.56 µH vs MAZO 0.56 µH. Saturation current 30.8 A (30% drop) vs MAZO 19 A typ. (30% drop); heating current 16 A (40 °C rise) vs MAZO 18 A typ. (40 °C rise). DCR 3.19 mΩ max vs MAZO 4.5 mΩ max. Body 6.65 × 6.45 × 3 mm vs MAZO 7.3 × 6.8 × 3 mm. Land pattern differs from MAZO's: two 5.5 × 1.45 mm pads 2.55 mm apart vs MAZO two 3.5 × 2.35 mm pads 3.7 mm apart (overall span differs by 2.95 mm). Verdict: MAZO figures are weaker, consider only with ample margin (MAZO Isat about 38% lower, Idc not lower at 40 °C rise, DCR slightly higher). Request a quote. Both parts are AEC-Q200.
How the figures are compared

Isat and Irms follow each datasheet's own definition, shown after the figure. MAZO figures are typical values from its spec table.

Recommended pads: pad width × pad length, then the gap between the two pads, from each datasheet, compared with MAZO's.

Engineering guides for this part

More parts in this category

Same footprint, other values

Same 7.3 × 6.8 mm body, by inductance.

Part numberLIsatIdcDCR maxHeightUnit price
VCMA-0630-R22-M-1A0.22 µH40 A24.5 A3 mΩ3 mm$0.30
VCMA-0630-R24-M-1A0.24 µH32 A23.5 A3.1 mΩ3 mm$0.30
VCMA-0630-R33-M-1A0.33 µH27 A21.5 A3.5 mΩ3 mm$0.30
VCMA-0630-R36-M-1A0.36 µH26 A20 A3.7 mΩ3 mm$0.30
VCMA-0630-R47-M-1A0.47 µH22 A19 A4.1 mΩ3 mm$0.30
VCMA-0630-R68-M-1A0.68 µH18 A16 A5.3 mΩ3 mm$0.30
VCMA-0630-R82-M-1A0.82 µH17 A14.5 A6 mΩ3 mm$0.23
VCMA-0630-1R0-M-1A1 µH15.5 A13.5 A7.4 mΩ3 mm$0.24
VCMA-0630-1R5-M-1A1.5 µH14.5 A12 A11 mΩ3 mm$0.23
VCMA-0630-2R2-M-1A2.2 µH12.5 A9.5 A15 mΩ3 mm$0.23
VCMA-0630-5R6-M-1A5.6 µH6.5 A5.5 A42 mΩ3 mm$0.33
VCMA-0630-6R8-M-1A6.8 µH6 A5 A48 mΩ3 mm$0.30

Same value, other sizes

Smallest first. A larger body usually carries more current; the pads differ.

Part numberLIsatIdcDCR maxBodyUnit price
VCMA-0420-R56-M-1A0.56 µH10.5 A8 A13 mΩ4.75 × 4.45 × 2 mm$0.28
VCMA-1040-R56-M-1A0.56 µH38 A26 A1.8 mΩ11.5 × 10.3 × 4 mm$0.52
VCMA-1350-R56-M-1A0.56 µH62 A36 A1.32 mΩ13.8 × 12.9 × 5 mm$0.72

Buy

Unit price · USD / piece$0.30For 5 pieces
Quantity pricingSelect a tier to set the quantity.
QuantityUnit priceExtended
5–49$0.3$1.50
50–149$0.22$11.00
150–499$0.191$28.65
500–2999$0.142$71.00
Merchandise subtotal$1.50Item amount only; excludes packaging, handling, shipping, duties and tax. Packaging and handling charges are shown in the cart. Shipping, duties and tax are confirmed separately.
Minimum order
5 pieces
Order multiple
1 piece
Availability
Factory stock
Dispatch preparation
2 days
Ships from ChinaShipping: DHL ExpressChoose a delivery country to see the transit estimate.

Dispatch preparation and shipping transit are separate. Arrival is estimated; the confirmed route and shipment tracking determine delivery.

Minimum order: 5; order in multiples of 1.
PackagingFor the selected quantity
Standard full-reel quantity
1500 pieces
Packed as
Cut tape · 5 pieces
Cut-tape fee
None
Online order limit
2999 pieces

Packaging and handling charges are shown in the cart. Shipping, duties and tax are confirmed separately.

Add this quantity to your cart to review order charges and the available payment steps. Sign in if prompted.

Can't find it? We'll source it — and check it fits.

Not sure it fits your tool/process? Ask an engineer to check

An MST engineer will review your requirement and reply to help with sourcing and compatibility.

Request sourcing & fit check

Selection and use

How to select

Choosing inductance

L ≈ (Vin − Vout) × Vout ÷ (Vin × fsw × ΔI), with ΔI at 20–40% of the output current. The series covers 0.22–22 µH in one body, so changing the value needs no new layout.

Saturation current Isat

the current at which inductance falls about 30%; keep the peak current below it.

Heating current Idc

the current that raises the part about 40 °C above a 25 °C ambient; ambient plus rise stays within 125 °C.

DC resistance

sets the conduction loss. Typical 2.5–175 mΩ across the series; use the maximum for loss budgets.

Rated voltage

75 V maximum; check it against the input voltage.

Height

Max 3.0 mm. More current: VCMA-1040; lower: VCMA-0420.

Industry and product applications

VCMA-0630-R56-M-1A is a VCMA-0630 series part for evaluation in automotive electronics.

Manufacturer-listed series applications

Automotive applications.

MAZO datasheet: VCMA-0630-XXX-M-1A, revision A2, 2025-11-26 — applications on page 1

Circuit applications to evaluate

  • Domain controllers
  • ADAS compute units
  • 12 V to 5 V / 3.3 V bucks
  • LED drivers and backlight
  • SEPIC / buck-boost front ends
  • BMS and on-board charger auxiliary supplies

These are series applications and engineering evaluation examples. Select VCMA-0630-R56-M-1A against the required inductance, peak and RMS current, switching frequency, temperature rise and PCB footprint. Inclusion here does not establish suitability for a particular design or qualification of the finished product.

Frequently asked questions

What are the key specifications of VCMA-0630-R56-M-1A?

VCMA-0630-R56-M-1A: Brand: MAZO / Mazotech; Series: VCMA-0630; Inductance L0: 0.56 µH ±20% (1 MHz, 1.0 V); DCR typ.: 3.9 mΩ; DCR max.: 4.5 mΩ; Heating current Idc typ.: 18 A. Full values are in the specifications table above.

Which parts can VCMA-0630-R56-M-1A be evaluated as an alternative to?

VCMA-0630-R56-M-1A is listed as an alternative to TDK SPM6530T-R56M, Bourns SRP6030CA-R56M, Bourns SRP6530A-R56M, Coilcraft XAL6030-561MEC, Würth Elektronik 744393440056 (same footprint class and nominal value). Request a quote with the RFQ form on this page.

What does VCMA-0630-R56-M-1A cost?

VCMA-0630-R56-M-1A is US$0.30 per piece, minimum order 5 pieces, with DHL shipping quoted by destination.

Can MST source a part number that is not listed?

Yes. Send the exact part number and quantity through the RFQ form and MST sources it and replies with a quote.