MAZO 0.47 µH shielded power inductor, Idc 10 A typ. – Alternative to Bourns SRP5030TA-R47M
- Inductance
- 0.47 µH
- Isat
- 18 A
- Idc
- 10 A
- DCR max
- 8.5 mΩ
- Brand
- MAZO
- Series
- VCMA-0530
- Size
- 5.7 × 5.4 × 3 mm
- Category
- MAZO power inductors
- Related applications
- Automotive / OBC
- Features
- AEC-Q200Magnetic shieldRoHSHalogen free
- Stock
- Factory stock

Applications and industries
Industries: Automotive · AEC-Q200 qualified
Manufacturer-listed applications: Automotive applications (datasheet); ADAS, cockpit, powertrain, body and central domain controllers (MAZO application areas)
MST engineering note — typical circuits: 12 V battery buck to 5 V / 3.3 V / core rails, SoC and ADAS processor point-of-load, LED driver and SEPIC / buck-boost stages. Low-to-mid current rails in compact modules.
Sources: VCMA-0530 datasheet · MAZO application areas
Selection tips
Selection tips
- Keep the peak current (DC load plus half the ripple) below Isat 18 A; Isat is 1.8× the 10 A heating-current rating.
- Copper loss at 10 A with DCR max 8.5 mΩ is about 0.85 W (I² × DCR); size copper and airflow for it.
- Use on rails at or below the 50 V rated voltage.
- Operating temperature -55 °C to +125 °C includes self-heating, so ambient plus temperature rise must stay inside it.
- AEC-Q200 is stated on the datasheet, so the part can enter an automotive qualification plan.
Specifications
Datasheet facts
- Recommended land pattern
- Two 2.5 × 1.9 mm pads, 2.2 mm apart, 6 mm overall
- Inductance test condition
- 1 MHz, 1.0 V, 25 °C
- Current definitions
- Isat: inductance drops about 30%; Idc: temperature rise about 40 °C
- Soldering
- Reflow per J-STD-020
- Operating temperature (ambient + self-heating)
- -55 ~ +125 °C
- Storage temperature
- -55 ~ +125 °C
- Packaging
- 2000 pieces per reel; tape pocket 5.7±0.10 × 5.9±0.10 × 3.3±0.15 mm
Datasheet VCMA-0530-XXX-M-1A, revision A2, 2025-11-26, page 4
Characteristic curves
Typical curves from the MAZO datasheet, for reference only.
Soldering and packaging
Alternative to these parts
VCMA-0530-R47-M-1A matches the parts below in footprint class and nominal value. Request a quote.
| Brand | Part number | L | Isat | Irms | DCR max | Size | Footprint | Recommended pads | VCMA-0530-R47-M-1A vs. this part |
|---|---|---|---|---|---|---|---|---|---|
| TDK | SPM5030T-R47M-HZSPM5030T-HZ | 0.47 µH | 11 A · 20% | 14 A · 40 °C | 5.39 mΩ | 5.2 × 5 × 3 mm | Pad-compatible | 2.2 × 1.5 mm, gap 2.7 mmClose to MAZO (0.5 mm off) | Weaker figures |
| Bourns | SRP5030TA-R47MSRP5030TA | 0.47 µH | 16 A · 20% | 12 A · 40 °C | 7.4 mΩ | 5.7 × 5.3 × 3 mm | Same footprint class | 1.8 × 2 mm, gap 2.5 mmDiffers from MAZO (0.7 mm off) | With margin; check the pads |
| Cyntec | VCMT053T-R47MN52MVCMT053T MN52M | 0.47 µH | 14 A · 20% | 12.4 A · 40 °C | 7.9 mΩ | 5.45 × 5.25 × 3 mm | Same footprint class | 2.79 × 1.905 mm, gap 2.946 mmDiffers from MAZO (0.756 mm off) | With margin; check the pads |
| Vishay | IHLP2020CZERR47M01IHLP-2020CZ-01 | 0.47 µH | 16 A · 20% | 12.2 A · 40 °C | 7.04 mΩ | 5.18 × 5.49 × 3 mm | Same footprint class | 2.79 × 1.905 mm, gap 2.946 mmDiffers from MAZO (0.756 mm off) | With margin; check the pads |
| Würth Elektronik | 744373360047WE-LHMI 5030 | 0.47 µH | 21.5 A · 30% | 12.3 A · 40 °C | 7.4 mΩ | 5.7 × 5.2 × 3 mm | Same footprint class | 1.8 × 2 mm, gap 2.5 mmDiffers from MAZO (0.7 mm off) | With margin; check the pads |
What each comparison means (5)
- TDK SPM5030T-R47M-HZ (SPM5030T-HZ): Same inductance, 0.47 µH vs MAZO 0.47 µH. Saturation current 11 A (20% drop) vs MAZO 18 A typ. (30% drop), rated on different bases so not directly comparable; heating current 14 A (40 °C rise) vs MAZO 10 A typ. (40 °C rise). DCR 5.39 mΩ max vs MAZO 8.5 mΩ max. Body 5.2 × 5 × 3 mm vs MAZO 5.7 × 5.4 × 3 mm. Land pattern close to MAZO's: two 2.2 × 1.5 mm pads 2.7 mm apart vs MAZO two 2.5 × 1.9 mm pads 2.2 mm apart (gap differs by 0.5 mm). Verdict: MAZO figures are weaker, consider only with ample margin (Idc about 29% lower at 40 °C rise, DCR slightly higher). Request a quote. Both parts are AEC-Q200.
- Bourns SRP5030TA-R47M: Same inductance, 0.47 µH vs MAZO 0.47 µH. Saturation current 16 A (20% drop) vs MAZO 18 A typ. (30% drop), rated on different bases so not directly comparable; heating current 12 A (40 °C rise) vs MAZO 10 A typ. (40 °C rise). DCR 7.4 mΩ max vs MAZO 8.5 mΩ max. Body 5.7 × 5.3 × 3 mm vs MAZO 5.7 × 5.4 × 3 mm. Land pattern differs from MAZO's: two 1.8 × 2 mm pads 2.5 mm apart vs MAZO two 2.5 × 1.9 mm pads 2.2 mm apart (pad width differs by 0.7 mm). Verdict: replaceable with design margin, pads need checking (Idc about 17% lower at 40 °C rise, DCR slightly higher). Request a quote. Both parts are AEC-Q200.
- Cyntec VCMT053T-R47MN52M (VCMT053T MN52M): Same inductance, 0.47 µH vs MAZO 0.47 µH. Saturation current 14 A (20% drop) vs MAZO 18 A typ. (30% drop), rated on different bases so not directly comparable; heating current 12.4 A (40 °C rise) vs MAZO 10 A typ. (40 °C rise). DCR 7.9 mΩ max vs MAZO 8.5 mΩ max. Body 5.45 × 5.25 × 3 mm vs MAZO 5.7 × 5.4 × 3 mm. Land pattern differs from MAZO's: two 2.79 × 1.905 mm pads 2.946 mm apart vs MAZO two 2.5 × 1.9 mm pads 2.2 mm apart (overall span differs by 0.756 mm). Verdict: replaceable with design margin, pads need checking (Idc about 19% lower at 40 °C rise, DCR slightly higher). Request a quote. Both parts are AEC-Q200.
- Vishay IHLP2020CZERR47M01 (IHLP-2020CZ-01): Same inductance, 0.47 µH vs MAZO 0.47 µH. Saturation current 16 A (20% drop) vs MAZO 18 A typ. (30% drop), rated on different bases so not directly comparable; heating current 12.2 A (40 °C rise) vs MAZO 10 A typ. (40 °C rise). DCR 7.04 mΩ max vs MAZO 8.5 mΩ max. Body 5.18 × 5.49 × 3 mm vs MAZO 5.7 × 5.4 × 3 mm. Land pattern differs from MAZO's: two 2.79 × 1.905 mm pads 2.946 mm apart vs MAZO two 2.5 × 1.9 mm pads 2.2 mm apart (overall span differs by 0.756 mm). Verdict: replaceable with design margin, pads need checking (Idc about 18% lower at 40 °C rise, DCR slightly higher). Request a quote.
- Würth Elektronik 744373360047 (WE-LHMI 5030): Same inductance, 0.47 µH vs MAZO 0.47 µH. Saturation current 21.5 A (30% drop) vs MAZO 18 A typ. (30% drop); heating current 12.3 A (40 °C rise) vs MAZO 10 A typ. (40 °C rise). DCR 7.4 mΩ max vs MAZO 8.5 mΩ max. Body 5.7 × 5.2 × 3 mm vs MAZO 5.7 × 5.4 × 3 mm. Land pattern differs from MAZO's: two 1.8 × 2 mm pads 2.5 mm apart vs MAZO two 2.5 × 1.9 mm pads 2.2 mm apart (pad width differs by 0.7 mm). Verdict: replaceable with design margin, pads need checking (MAZO Isat about 16% lower, Idc about 19% lower at 40 °C rise, DCR slightly higher). Request a quote.
How the figures are compared
Isat and Irms follow each datasheet's own definition, shown after the figure. MAZO figures are typical values from its spec table.
Recommended pads: pad width × pad length, then the gap between the two pads, from each datasheet, compared with MAZO's.
More parts in this category
- MAZO 1.5 µH 8 A 50 V shielded power inductor
- MAZO 2.2 µH 50 V shielded power inductor
- MAZO 3.3 µH 50 V shielded power inductor
- MAZO 4.7 µH 50 V shielded power inductor
- MAZO 6.8 µH 5.7 × 5.4 × 3.0 mm shielded power inductor
- MAZO 0.33 µH 5.7 × 5.4 × 3.0 mm shielded power inductor
- MAZO 0.68 µH 50 V Shielded Power Inductor 5.7 × 5.4 × 3.0 mm
- MAZO 10 µH 75 V shielded power inductor
- MAZO 15 µH 75 V AEC-Q200 shielded power inductor
- MAZO 1 µH 75 V 15.5 A shielded power inductor
- MAZO 1.5 µH 12 A shielded power inductor
- MAZO 22 µH 75 V shielded power inductor
Same footprint, other values
Same 5.7 × 5.4 mm body, by inductance.
| Part number | L | Isat | Idc | DCR max | Height | Unit price |
|---|---|---|---|---|---|---|
| VCMA-0530-R33-M-1A | 0.33 µH | 19 A | 16 A | 5 mΩ | 3 mm | $0.29 |
| VCMA-0530-R68-M-1A | 0.68 µH | 15 A | 9 A | 9.8 mΩ | 3 mm | $0.30 |
| VCMA-0530-1R0-M-1A | 1 µH | 11 A | 8.5 A | 13 mΩ | 3 mm | $0.30 |
| VCMA-0530-1R5-M-1A | 1.5 µH | 10 A | 8 A | 18 mΩ | 3 mm | $0.30 |
| VCMA-0530-2R2-M-1A | 2.2 µH | 8.5 A | 5.5 A | 26 mΩ | 3 mm | $0.30 |
| VCMA-0530-3R3-M-1A | 3.3 µH | 7.5 A | 4.8 A | 37 mΩ | 3 mm | $0.27 |
| VCMA-0530-4R7-M-1A | 4.7 µH | 5.5 A | 3.5 A | 58 mΩ | 3 mm | $0.30 |
| VCMA-0530-6R8-M-1A | 6.8 µH | 4 A | 3 A | 90 mΩ | 3 mm | $0.33 |
| VCMA-0530-100-M-1A | 10 µH | 3 A | 2.5 A | 125 mΩ | 3 mm | $0.20 |
Same value, other sizes
Smallest first. A larger body usually carries more current; the pads differ.
| Part number | L | Isat | Idc | DCR max | Body | Unit price |
|---|---|---|---|---|---|---|
| VCMA-0420-R47-M-1A | 0.47 µH | 12 A | 8.5 A | 12 mΩ | 4.75 × 4.45 × 2 mm | $0.22 |
| VCMA-0630-R47-M-1A | 0.47 µH | 22 A | 19 A | 4.1 mΩ | 7.3 × 6.8 × 3 mm | $0.30 |
| VCMA-1040-R47-M-1A | 0.47 µH | 45 A | 27 A | 1.7 mΩ | 11.5 × 10.3 × 4 mm | $0.52 |
| VCMA-1350-R47-M-1A | 0.47 µH | 64 A | 43 A | 0.9 mΩ | 13.8 × 12.9 × 5 mm | $0.75 |
Buy
| Quantity | Unit price | Extended |
|---|---|---|
| 5–49 | $0.3 | $1.50 |
| 50–149 | $0.22 | $11.00 |
| 150–499 | $0.182 | $27.30 |
| 500–2999 | $0.14 | $70.00 |
- Minimum order
- 5 pieces
- Order multiple
- 1 piece
- Availability
- Factory stock
- Dispatch preparation
- 2 days
Dispatch preparation and shipping transit are separate. Arrival is estimated; the confirmed route and shipment tracking determine delivery.
- Standard full-reel quantity
- 2000 pieces
- Packed as
- Cut tape · 5 pieces
- Cut-tape fee
- None
- Online order limit
- 2999 pieces
Packaging and handling charges are shown in the cart. Shipping, duties and tax are confirmed separately.
Add this quantity to your cart to review order charges and the available payment steps. Sign in if prompted.
Can't find it? We'll source it — and check it fits.
Not sure it fits your tool/process? Ask an engineer to check
An MST engineer will review your requirement and reply to help with sourcing and compatibility.
Selection and use
How to select
Choosing inductance
L ≈ (Vin − Vout) × Vout ÷ (Vin × fsw × ΔI), with ΔI at 20–40% of the output current. The series covers 0.33–10 µH in one body, so changing the value needs no new layout.
Saturation current Isat
the current at which inductance falls about 30%; keep the peak current below it.
Heating current Idc
the current that raises the part about 40 °C above a 25 °C ambient; ambient plus rise stays within 125 °C.
DC resistance
sets the conduction loss. Typical 4.5–110 mΩ across the series; use the maximum for loss budgets.
Rated voltage
50 V maximum; check it against the input voltage.
Height
Max 3.0 mm. Lower: VCMA-0420; same height, more current: VCMA-0630.
Industry and product applications
VCMA-0530-R47-M-1A is a VCMA-0530 series part for evaluation in automotive electronics.
Manufacturer-listed series applications
Automotive applications.
MAZO datasheet: VCMA-0530-XXX-M-1A, revision A2, 2025-11-26 — applications on page 1
Circuit applications to evaluate
These are series applications and engineering evaluation examples. Select VCMA-0530-R47-M-1A against the required inductance, peak and RMS current, switching frequency, temperature rise and PCB footprint. Inclusion here does not establish suitability for a particular design or qualification of the finished product.
Frequently asked questions
What are the key specifications of VCMA-0530-R47-M-1A?
VCMA-0530-R47-M-1A: Brand: MAZO / Mazotech; Series: VCMA-0530; Inductance L0: 0.47 µH ±20% (1 MHz, 1.0 V); DCR typ.: 7.5 mΩ; DCR max.: 8.5 mΩ; Heating current Idc typ.: 10 A. Full values are in the specifications table above.
Which parts can VCMA-0530-R47-M-1A be evaluated as an alternative to?
VCMA-0530-R47-M-1A is listed as an alternative to TDK SPM5030T-R47M-HZ, Bourns SRP5030TA-R47M, Cyntec VCMT053T-R47MN52M, Vishay IHLP2020CZERR47M01, Würth Elektronik 744373360047 (same footprint class and nominal value). Request a quote with the RFQ form on this page.
What does VCMA-0530-R47-M-1A cost?
VCMA-0530-R47-M-1A is US$0.30 per piece, minimum order 5 pieces, with DHL shipping quoted by destination.
Can MST source a part number that is not listed?
Yes. Send the exact part number and quantity through the RFQ form and MST sources it and replies with a quote.