MAZO 10 µH shielded power inductor, Idc 8.5 A typ. – Alternative to Cyntec CMLB135T-100MS
- Inductance
- 10 µH
- Isat
- 14 A
- Idc
- 8.5 A
- DCR max
- 21.5 mΩ
- Brand
- MAZO
- Series
- VCMA-1350
- Size
- 13.8 × 12.9 × 5 mm
- Category
- MAZO power inductors
- Related applications
- Automotive / OBC
- Features
- AEC-Q200Magnetic shieldRoHSHalogen free
- Stock
- Factory stock

Applications and industries
Industries: Automotive · AEC-Q200 qualified
Manufacturer-listed applications: Automotive applications (datasheet); ADAS, cockpit, powertrain, body and central domain controllers (MAZO application areas)
MST engineering note — typical circuits: 12 V battery buck to 5 V / 3.3 V / core rails, SoC and ADAS processor point-of-load, LED driver and SEPIC / buck-boost stages. Higher inductance and current, e.g. battery-input front ends.
Sources: VCMA-1350 datasheet · MAZO application areas
Selection tips
Selection tips
- Keep the peak current (DC load plus half the ripple) below Isat 14 A; Isat is 1.6× the 8.5 A heating-current rating.
- Copper loss at 8.5 A with DCR max 21.5 mΩ is about 1.55 W (I² × DCR); size copper and airflow for it.
- Use on rails at or below the 75 V rated voltage.
- Operating temperature −55 °C to +125 °C includes self-heating, so ambient plus temperature rise must stay inside it.
- AEC-Q200 is stated on the datasheet, so the part can enter an automotive qualification plan.
Specifications
Datasheet facts
- Recommended land pattern
- Two 5 × 3.25 mm pads, 8 mm apart, 14.5 mm overall
- Inductance test condition
- 1 MHz, 1.0 V, 25 °C
- Current definitions
- Isat: inductance drops about 30%; Idc: temperature rise about 40 °C
- Soldering
- Reflow per J-STD-020
- Operating temperature (ambient + self-heating)
- -55 ~ +125 °C
- Storage temperature
- -55 ~ +125 °C
- Packaging
- 500 pieces per reel; tape pocket 13.4±0.10 × 14.4±0.10 × 5.4±0.15 mm
Datasheet VCMA-1350-XXX-M-1A, revision A4, 2025-11-26, page 4
Characteristic curves
Typical curves from the MAZO datasheet, for reference only.
Soldering and packaging
Alternative to these parts
VCMA-1350-100-M-1A matches the parts below in footprint class and nominal value. Request a quote.
| Brand | Part number | L | Isat | Irms | DCR max | Size | Footprint | Recommended pads | VCMA-1350-100-M-1A vs. this part |
|---|---|---|---|---|---|---|---|---|---|
| Cyntec | CMLB135T-100MSCMLB135T | 10 µH | 13 A · 30% | 9 A · 40 °C | 22 mΩ | 13.45 × 12.6 × 4.8 mm | Pad-compatible | 5 × 3.25 mm, gap 8 mmSame as MAZO | Drop-in candidate |
| Bourns | SRP1245A-100MSRP1245A | 10 µH | 16 A · 20% | 9 A · 40 °C | 25.5 mΩ | 13.5 × 12.5 × 4.8 mm | Pad-compatible | 5 × 3.1 mm, gap 8 mmClose to MAZO (0.3 mm off) | With design margin |
| Vishay | IHLP5050EZEK100M01IHLP-5050EZ-01 | 10 µH | 16 A · 20% | 9 A · 40 °C | 25.5 mΩ | 13.2 × 12.9 × 5 mm | Same footprint class | 4.953 × 3.226 mm, gap 8.28 mmClose to MAZO (0.28 mm off) | With margin; check the pads |
| Vishay | IHLP5050EZEK100MA1IHLP-5050EZ-A1 | 10 µH | 16 A · 20% | 9 A · 40 °C | 25.5 mΩ | 13.2 × 12.9 × 5 mm | Same footprint class | 4.953 × 3.226 mm, gap 8.28 mmClose to MAZO (0.28 mm off) | With margin; check the pads |
| Würth Elektronik | 7443550101WE-HCI 1350 | 10 µH | 10 A · 30% | 8.5 A · 50 °C | 14.1 mΩ | 13 × 12.8 × 4.7 mm | Same footprint class | 5 × 4.5 mm, gap 6 mmDiffers from MAZO (2 mm off) | Weaker figures |
What each comparison means (5)
- Cyntec CMLB135T-100MS: Same inductance, 10 µH vs MAZO 10 µH. Saturation current 13 A (30% drop) vs MAZO 14 A typ. (30% drop); heating current 9 A (40 °C rise) vs MAZO 8.5 A typ. (40 °C rise). DCR 22 mΩ max vs MAZO 21.5 mΩ max. Body 13.45 × 12.6 × 4.8 mm vs MAZO 13.8 × 12.9 × 5 mm, MAZO 0.2 mm taller. Same land pattern as MAZO (two 5 × 3.25 mm pads 8 mm apart). Verdict: drop-in candidate (MAZO Isat not lower, Idc about 6% lower at 40 °C rise, DCR lower, less conduction loss). Request a quote.
- Bourns SRP1245A-100M: Same inductance, 10 µH vs MAZO 10 µH. Saturation current 16 A (20% drop) vs MAZO 14 A typ. (30% drop), rated on different bases so not directly comparable; heating current 9 A (40 °C rise) vs MAZO 8.5 A typ. (40 °C rise). DCR 25.5 mΩ max vs MAZO 21.5 mΩ max. Body 13.5 × 12.5 × 4.8 mm vs MAZO 13.8 × 12.9 × 5 mm, MAZO 0.2 mm taller. Land pattern close to MAZO's: two 5 × 3.1 mm pads 8 mm apart vs MAZO two 5 × 3.25 mm pads 8 mm apart (overall span differs by 0.3 mm). Verdict: replaceable with design margin (Idc about 6% lower at 40 °C rise, DCR lower, less conduction loss). Request a quote. Both parts are AEC-Q200.
- Vishay IHLP5050EZEK100M01 (IHLP-5050EZ-01): Same inductance, 10 µH vs MAZO 10 µH. Saturation current 16 A (20% drop) vs MAZO 14 A typ. (30% drop), rated on different bases so not directly comparable; heating current 9 A (40 °C rise) vs MAZO 8.5 A typ. (40 °C rise). DCR 25.5 mΩ max vs MAZO 21.5 mΩ max. Body 13.2 × 12.9 × 5 mm vs MAZO 13.8 × 12.9 × 5 mm. Land pattern close to MAZO's: two 4.953 × 3.226 mm pads 8.28 mm apart vs MAZO two 5 × 3.25 mm pads 8 mm apart (gap differs by 0.28 mm). Verdict: replaceable with design margin, pads need checking (Idc about 6% lower at 40 °C rise, DCR lower, less conduction loss). Request a quote.
- Vishay IHLP5050EZEK100MA1 (IHLP-5050EZ-A1): Same inductance, 10 µH vs MAZO 10 µH. Saturation current 16 A (20% drop) vs MAZO 14 A typ. (30% drop), rated on different bases so not directly comparable; heating current 9 A (40 °C rise) vs MAZO 8.5 A typ. (40 °C rise). DCR 25.5 mΩ max vs MAZO 21.5 mΩ max. Body 13.2 × 12.9 × 5 mm vs MAZO 13.8 × 12.9 × 5 mm. Land pattern close to MAZO's: two 4.953 × 3.226 mm pads 8.28 mm apart vs MAZO two 5 × 3.25 mm pads 8 mm apart (gap differs by 0.28 mm). Verdict: replaceable with design margin, pads need checking (Idc about 6% lower at 40 °C rise, DCR lower, less conduction loss). Request a quote. Both parts are AEC-Q200.
- Würth Elektronik 7443550101 (WE-HCI 1350): Same inductance, 10 µH vs MAZO 10 µH. Saturation current 10 A (30% drop) vs MAZO 14 A typ. (30% drop); heating current 8.5 A (50 °C rise) vs MAZO 8.5 A typ. (40 °C rise), rated on different bases so not directly comparable. DCR 14.1 mΩ typ vs MAZO 18.5 mΩ typ. Body 13 × 12.8 × 4.7 mm vs MAZO 13.8 × 12.9 × 5 mm, MAZO 0.3 mm taller. Land pattern differs from MAZO's: two 5 × 4.5 mm pads 6 mm apart vs MAZO two 5 × 3.25 mm pads 8 mm apart (gap differs by 2 mm). Verdict: MAZO figures are weaker, consider only with ample margin (MAZO Isat not lower, DCR slightly higher). Request a quote. Both parts are AEC-Q200.
How the figures are compared
Isat and Irms follow each datasheet's own definition, shown after the figure. MAZO figures are typical values from its spec table.
Recommended pads: pad width × pad length, then the gap between the two pads, from each datasheet, compared with MAZO's.
More parts in this category
- MAZO 8.2 µH 11 A shielded power inductor
- MAZO 0.22 µH 70 A shielded power inductor
- MAZO VCMA-1040 0.36 µH 32 A shielded power inductor
- MAZO 0.47 µH 45 A shielded power inductor
- MAZO 0.56 µH 38 A shielded power inductor
- MAZO 0.68 µH 23 A shielded power inductor
- MAZO 15 µH 10 A shielded power inductor
- MAZO 1 µH 26 A shielded power inductor
- MAZO VCMA-1350 1.5 µH 23 A shielded power inductor
- MAZO 22 µH 75 V 6.5 A shielded power inductor
- MAZO 2.2 µH 21 A shielded power inductor
- MAZO 33 µH 5.5 A shielded power inductor
Same footprint, other values
Same 13.8 × 12.9 mm body, by inductance.
| Part number | L | Isat | Idc | DCR max | Height | Unit price |
|---|---|---|---|---|---|---|
| VCMA-1350-2R2-M-1A | 2.2 µH | 28 A | 21 A | 4.6 mΩ | 5 mm | $0.72 |
| VCMA-1350-3R3-M-1A | 3.3 µH | 24 A | 16 A | 6.9 mΩ | 5 mm | $0.75 |
| VCMA-1365-3R3-M-1A | 3.3 µH | 25 A | 22 A | 4.5 mΩ | 6.5 mm | $0.79 |
| VCMA-1350-4R7-M-1A | 4.7 µH | 20.5 A | 14 A | 9.2 mΩ | 5 mm | $0.75 |
| VCMA-1365-4R7-M-1A | 4.7 µH | 24 A | 20 A | 6.9 mΩ | 6.5 mm | $0.79 |
| VCMA-1350-5R6-M-1A | 5.6 µH | 20 A | 12 A | 12 mΩ | 5 mm | $0.75 |
| VCMA-1365-5R6-M-1A | 5.6 µH | 22 A | 18 A | 8.2 mΩ | 6.5 mm | $0.90 |
| VCMA-1350-6R8-M-1A | 6.8 µH | 16.5 A | 11.5 A | 13.5 mΩ | 5 mm | $0.75 |
| VCMA-1365-6R8-M-1A | 6.8 µH | 20 A | 16 A | 11 mΩ | 6.5 mm | $0.93 |
| VCMA-1365-100-M-1A | 10 µH | 18 A | 15 A | 17 mΩ | 6.5 mm | $0.93 |
| VCMA-1350-150-M-1A | 15 µH | 10 A | 7.8 A | 26 mΩ | 5 mm | $0.75 |
| VCMA-1365-150-M-1A | 15 µH | 13 A | 10 A | 24 mΩ | 6.5 mm | $1.03 |
Same value, other sizes
Smallest first. A larger body usually carries more current; the pads differ.
| Part number | L | Isat | Idc | DCR max | Body | Unit price |
|---|---|---|---|---|---|---|
| VCMA-0420-100-M-1A | 10 µH | 2.2 A | 1.7 A | 281 mΩ | 4.75 × 4.45 × 2 mm | $0.41 |
| VCMA-0530-100-M-1A | 10 µH | 3 A | 2.5 A | 125 mΩ | 5.7 × 5.4 × 3 mm | $0.20 |
| VCMA-0630-100-M-1A | 10 µH | 5.5 A | 4.1 A | 67 mΩ | 7.3 × 6.8 × 3 mm | $0.21 |
| VCMA-1040-100-M-1A | 10 µH | 9 A | 7.2 A | 30 mΩ | 11.5 × 10.3 × 4 mm | $0.62 |
Buy
| Quantity | Unit price | Extended |
|---|---|---|
| 5–49 | $0.75 | $3.75 |
| 50–149 | $0.54 | $27.00 |
| 150–499 | $0.436 | $65.40 |
| 500–2999 | $0.338 | $169.00 |
- Minimum order
- 5 pieces
- Order multiple
- 1 piece
- Availability
- Factory stock
- Dispatch preparation
- 2 days
Dispatch preparation and shipping transit are separate. Arrival is estimated; the confirmed route and shipment tracking determine delivery.
- Standard full-reel quantity
- 500 pieces
- Packed as
- Cut tape · 5 pieces
- Cut-tape fee
- None
- Online order limit
- 2999 pieces
Packaging and handling charges are shown in the cart. Shipping, duties and tax are confirmed separately.
Add this quantity to your cart to review order charges and the available payment steps. Sign in if prompted.
Can't find it? We'll source it — and check it fits.
Not sure it fits your tool/process? Ask an engineer to check
An MST engineer will review your requirement and reply to help with sourcing and compatibility.
Selection and use
How to select
Choosing inductance
L ≈ (Vin − Vout) × Vout ÷ (Vin × fsw × ΔI), with ΔI at 20–40% of the output current. The series covers 0.22–33 µH in one body, so changing the value needs no new layout.
Saturation current Isat
the current at which inductance falls about 30%; keep the peak current below it.
Heating current Idc
the current that raises the part about 40 °C above a 25 °C ambient; ambient plus rise stays within 125 °C.
DC resistance
sets the conduction loss. Typical 0.54–50 mΩ across the series; use the maximum for loss budgets.
Rated voltage
75 V maximum; check it against the input voltage.
Height
Max 5.0 mm. VCMA-1365 shares the land pattern at 6.5 mm with more inductance; smaller: VCMA-1040.
Industry and product applications
VCMA-1350-100-M-1A is a VCMA-1350 series part for evaluation in automotive electronics.
Manufacturer-listed series applications
Automotive applications.
MAZO datasheet: VCMA-1350-XXX-M-1A, revision A4, 2025-11-26 — applications on page 1
Circuit applications to evaluate
These are series applications and engineering evaluation examples. Select VCMA-1350-100-M-1A against the required inductance, peak and RMS current, switching frequency, temperature rise and PCB footprint. Inclusion here does not establish suitability for a particular design or qualification of the finished product.
Frequently asked questions
What are the key specifications of VCMA-1350-100-M-1A?
VCMA-1350-100-M-1A: Brand: MAZO / Mazotech; Series: VCMA-1350; Inductance L0: 10 µH ±20% (1 MHz, 1.0 V); DCR typ.: 18.5 mΩ; DCR max.: 21.5 mΩ; Heating current Idc typ.: 8.5 A. Full values are in the specifications table above.
Which parts can VCMA-1350-100-M-1A be evaluated as an alternative to?
VCMA-1350-100-M-1A is listed as an alternative to Cyntec CMLB135T-100MS, Bourns SRP1245A-100M, Vishay IHLP5050EZEK100M01, Vishay IHLP5050EZEK100MA1, Würth Elektronik 7443550101 (same footprint class and nominal value). Request a quote with the RFQ form on this page.
What does VCMA-1350-100-M-1A cost?
VCMA-1350-100-M-1A is US$0.75 per piece, minimum order 5 pieces, with DHL shipping quoted by destination.
Can MST source a part number that is not listed?
Yes. Send the exact part number and quantity through the RFQ form and MST sources it and replies with a quote.